Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! voice traffic- bandwidth
Hi Experts..Pls help me in setting up QoS for my company. I have MPLS circuit for my all company locations. Main locations has 60mb MPLS circuit and branch locations has 20mb each. I have CME in my main location to which VOIP phones are registered. S...
I have a stack of three 3750X-48 switches, all with IPSERVICES. I have another stack of three 3750X-48 switches, all with IPBASE. The issue is that both are in production and each has the wrong license. Is there a way to demote one stack and move ...
Resolved! "negotiation auto" issue
There is a problem about "negotiation auto" in Cisco ASR 901. The case is that I config my port in "negotiation-auto" on ASR901. If the-other-side device(non-Cisco) sets it's port in force-up/speed 100. My port will be nego-auto/100-half. From my und...
Hi guys, Pls help me to explain a multicast problem: I have a topology like this: source(224.6.6.6)--R1---R2(RP)---R4---R5---R6---Receiver I use GNS3 lab, PIM-SM, R2 is RP. So I think between R2--R4--R5--R6 just see the shared tree, but when i show i...
Resolved! Access to trunk port clarification
Hello-I am looking to clarify a point of confusion for myself regrading connecting an access port to a trunk port. Consider the following switchport config on switch1:Switch#1interface GigabitEthernet0/5 switchport switchport access vlan 6 ....and ...
Hi Guys,I have a hard time configuring selective QinQ on 4900M platform. What I would like to achieve is to have some VLANs (e.g. 1-5) put into QinQ VLAN (e.g. 699) and to pass other VLANs (e.g. 132,133) without outer tag. Here is my configuration:S...
Is there anyway to get interface statistics from all interfaces regardless of what vdc they are in? Trying to setup solarwinds to monitor them all. Thanks,Alex
I have two Nexus 5596 connected to my core switches (Cisco 4500). EIGRP is running on both, and I'd like to advertise new L3 networks from the Nexus side to my core, but not sure how to do this. Here are some of the config's: router eigrp RCU-EIGRP-A...
If some can supply a sample of what the 3rd Nexus Switch configuration. Nexus-1 Configvrf context managementip route 0.0.0.0/0 192.168.50.1vlan 1vlan 10name ISCSI_VLANvpc domain 1peer-keepalive destination 192.168.50.242peer-gatewayinterface port-cha...
Hello, every docs and manual say "connect Cisco Power Adapter 48VDC PoE Input Jack" but searching in the networks nobody sells this adapter, anyone know where ???
Dears,My customer has Oracle servers dual connected to two 6500 switches. It has one ip address but different MAC addresses on each switch. They want to migrate the 6500 to VSS. The question now, what will happen to this setup after migration. Will i...
HiI have a problem here , cdp neighbor shows the same switch as the neighbor and the real connected switchh . I know it will show only the real connected switch if i shut and no sh . What i just want know is it a symptom for something else Dist#sh...
I have a network with two sites. Both site has the 3750 as a the core switch. One site is running code 12.2(50)SE2 and other site is running code 12.2(58)SE2 .Site P - QoS working fine. 12.2(58)SE2Site W - QoS not working. 12.2(50)SE2Site P, WAN - ...
We're having an issue with the above blade installed in a Catalyst 6506. It seems that when configuring the port channel, the port channel is automatically trunked. I haven't found a way to disable this as of yet and am thinking it may be just a li...
Has anyone came across this?Online Diagnostic of Supervisor Engine 720 (Hot): Test 35, Error code 43 (DIAG_CHECK_ETHER_PAK_ERROR)The complete diagnostic level was enabled on the system:#show diagnostic result module 6 failure detailCurrent bootup dia...
