Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hi,This question probably results from a flaw in my understanding of network layer 2 versus layer 3 and VLANs so any additional context in that regard would be very welcome If I've got 2 systems on difference VLANs that are connected to ports on the ...
Hello Guys I have simple doubt. Please try to guide me. Its with respect to Network Device A? 1. With a network wide mask of 255.255.255.128, each interface does not require an IP address. 2. With a network wide mask of 255.255.255.0, it must be a La...
Hello all,I have a Catalyst 6509-E with SUP2T and a WS-68xx series SFP line card. On this line card I will have 5 trunk connections going to ME3400 4 port access switches. There is one tagged VLAN allowed on all trunk ports and it is the same across ...
I have installed a (3) switch stack of Catalyst 3850 switches. I installed a 10G module in the 1st switch (the master) configured it and plugged it into the network and all works fine. Now I would like to add a second 10 Gigabit Ethernet connection t...
Hi Expert,I am using a CISCO WS-C6503-E box. My CISCO box is currently up with build Version 12.2(33)SXI3. My task is to test the IP unnumbered feature with CISCO box. I have read somewhere that CISCO WS-C6503-E supports IP unnumbered on vlan routing...
Hello everybody,I have a problem with my wireless controller.Somehow it will not add more AP's then 48, i have a license for 100 AP's.Is there a setting then can have been changed.Now the other access points (15) are associating with the wrong WLC.ev...
I have a sm-es2-24 in a 2911. I am getting the following in syslog:%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/25, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/25, changed state to down%LIN...
Hi All,I set up enable password as well as telnet password on cisco 881-k9.with the same password :kadd2013no username confuguredwhen i saved the config , i was unable to login again using the same password i configured
hi, Cisco Experts:I am not a network expert, so I need advices:Example:Customer has X 2 N5596, X 2 N2224TP and X 2 CAT6509E & others like UCS 5108 Chassis, etc.Q1.Customer has X 2 10G Ethernet Uplinks from N5596-A to CAT6509E-A.Customer has X 2 10G E...
hi all ,assume i have a class map x and i have policy map ynow in have policy-map y macthed the class x and gave it gurantee bw 1 Mbpsand left the class default without modification.the quewstion is how to give certian limit to the policy-map as a...
Resolved! DSCP value
Hi everybodyI hope you guys are doing fine. I got stumped by dscp value.Let say we have different traffics that we have mapped to different dscp values;A packet received with dscp " EF, and another packet is received with dscp CS7Which packet has h...
Hello.Looking for some assistance on the following please, I'll try to include a lot of detail:I noticed we're receiving repeating messages on a pair of Nexus 5548UP switches, regarding duplicate IP's, and the IP's in question are the mgmt0 of each r...
Hello Gents,There is specific design where Cisco ASA5585-SSP40 HA cluster connected to 1st N7K VPC domain with vPC port-channel. This domain consequently connected to 2nd N7K VPC domain. Two servers are single- and non-vpc connected to the latter VPC...
How to configure HSRP for IOS-XR on bvi interface instead L3 interface considering also ethernet bundle?
Hi,Hopoing someone could help clarify if the below config could work, or if it is just a no no.I am dealing with 2 DC's operating with a stretcheld LAN configuration using plain dot1q. We have a 1GB LAN link between the 2 of them and an older 100MB...
