Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Nexus 5548

                   We seem to have a strange issue that started yesterday.  We have n1000v connected to 2 x 5548's running 6.0(2)N1(2).We have 2 machines connected to vlan that is on N1000 port profile and n5548 with hsrp default gateway.The 2 machin...

BGP, VRF and PBR ("set vrf")

Hi networkers!Requirements:- 2 locations (OFFICE, DC) in the same town- each having two active WAN connections (carrying individual routing domains): The default Any2Any WAN (where several other locations are connected to) and a client specific MC WA...

JOEPI1234 by • Level 1
  • 625 Views
  • 0 replies
  • 0 Helpful votes

4507R+E with Sup 7-E in ROMMON

Hi,Without realizing that the ROMMON version on the platform is older (15.0(1r)SG5) then the minimum required 15.0(1r) SG7 for VSS, I converted the switch running IOS 3.4.0 SG to VSS. It took the commands and reloaded and went straight into ROMMON mo...

rick505d3 by • Level 1
  • 946 Views
  • 1 replies
  • 0 Helpful votes

Nexus HSRP

Hi,I have a customer that is stretching VLANs between DC's using dark fibre. Each DC will have a pair of Nexus 5548UPs.The question is can I run HSRP between the Nexus switches in the different DC's or can this only be between the paired Nexus switch...

Linksys SRW2008P reset

Hello.I have a linksys SRW2008P 8 port gigabit switch, i need to get access to it to configure it but i dont know the admin password, i have tried the default admin with blank password but does not work. How do i reset this switch to factory defaults...

cisco 3850 as edge switch in data center

Hi,I am having a dilema when it comes to replace the 2 cisco 3750 switches in the datacenter. They have links to Nexus 5000, where the servers and storage are connected, act as main L3 devices, where MPLS traffic from branches also comes and where th...

Nexus 5k connected to dual 4506-E w/VSS

We're in the process of several upgrades. Part of these upgrades include turning on VSS in our core on two 4506E and installing a Nexus 5k with UCS in the data center. I'm planning to configure the links between Nexus and 4506E as layer 3 port channe...

LACP,same speed,duplex,native vlan,vlan range

                   does LACP require same  native vlan, vlan range on physical port and logical interface?                  such as                  I config vlan range on physical interface for vlan 10-100                   and config vlan range on ...

fly by • Level 2
  • 553 Views
  • 3 replies
  • 0 Helpful votes

IOS upgrade 6509-E with sup32

                   I have a 6509E with supervisor32 modules  currently running3223-ipservicesk9_wan-mz.122-33.SXI5.binWent to the Cisco Feature Navigation and believe I can go to 3223-ipservicesk9_wan-mz.122-33.SXI12.binWas wondering if I am correct?...

Resolved! NX-7000 MGMT INT

Hello, If I already assigned an IP address to mgmt0 on SUP1 and connected it to the network, is there another mgmt int for SUP2 to assign an IP address to?http://www.cisco.com/en/US/docs/switches/datacenter/hw/nexus7000/installation/guide/n7k_connect...

Load more