Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have installed a EHWIC-4ESG  card into my 2911 router running IOS Ver 15.1(4)M2.  When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0."  Am I missing a step, do I have change somethin...

Hi. I have two Cat6506 (redundant collapsed-core config) configured w/  RPVST+ and connected to this are a series of Cat2950s configured with  PVST.  My question is, is this a good practice configuration of STP? If not whats the best practise .What I...

Hi,we would like to match mpls packets via an ACL on nexus 5k to send them into a certain QoS-group. Incoming interface is eth 1/8. Is this possible with the following configuration?I ask, because in the ACL we have permt IP any any but MPLS tagged f...

JAN HASSE by Level 1
  • 1262 Views
  • 4 replies
  • 0 Helpful votes

Hi Friends,I've configured my router LAN interface with secondary IP address, with & without ip-helper address.Option (1)interface GigabitEthernet0/0 description *** To LAN *** ip address 192.212.32.1 255.255.255.128 secondary ip address 192.234.212....

Hiwe have core switch in our network connected to ASAon switch ve have vlans:vlan 20 inside   ip address 172.20.20.0vlan 30 dmz     ip address 172.30.30.0interface vlan 20ip address 172.20.20.254interface vlan 30 ip address 172.30.30.254ip route 0.0....

I have a 7600 with ws-sup750 and when it boots it displays these errors:Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupportCopyrigh...

Hi all,I have the following on my 6509:Mod  Port Model              Serial #    Versions---- ---- ------------------ ----------- -------------------------------------  1   10  WS-SVC-WISM-1-K9   XXXXXXXXXXX Hw : 2.2                                   ...

tuan dang by Level 1
  • 565 Views
  • 1 replies
  • 0 Helpful votes

Hi Netprolet us talking HSRP,the blow config is it acceptable? no HSRP group for each VLAN!what is the pros and consinterface Vlan250 ip address 10.250.200.2 255.255.255.0 standby ip 10.250.200.1 standby preempt!!!interface Vlan251 ip address 10.251....

Hi All, I have problem with my switch please help me ! I have cisco switch 3560X and I try to configure it with more that 2000 VLANs but I got an error as below. How many VLANs can cisco switch support ?Switch(config)#vlan 2-4000Switch(config-vlan)#e...

Pok LY by Level 1
  • 1986 Views
  • 1 replies
  • 0 Helpful votes

Hi,I own a Cisco 892W router. The router has 2 WAN ports and 8 switch ports. Now I know - -WAN ports can create sub interfaces, assigne IPs, cannot be assigned to a VLAN - sounds very much like a routing port. (sh interface gives - Hardware is PQII_P...

Hi all,I'm attempting to configure Classification and Marking on our access switches using the MQC model. The Switches are 3750's running IPBase Version 12.2(35)SE. For some reason when I activate the policy-map on an interface, no traffic is being t...

hi! I've the setup as per the diagram attached. I try to setup w ccp in our env. I noticed that the wccp command will only work on the interface level if i turn the switch port into no switchport. Here are the draft of the command. The objective is t...

dave dave by Level 1
  • 2209 Views
  • 7 replies
  • 0 Helpful votes