Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hello,I cannot seem to find any information or configuration examples of using a Cisco IOS DHCP server to update A records on a local dns server.I would like to have the router that is running dhcp update the records for a few windows workstation to ...
Resolved! Jumbo frames on SGE2000/SGE2000P
According to the data from the old Linksys page for these products, the SGE2000/SGE2000P has "mini jumbo frame support (1600 bytes)". According to the data sheet from the new Cisco page these products have "jumbo frame support up to 10K". There is no...
Resolved! configuring rapid spanning tree
folksi have 2 * 3560es set up for resilience with 2 uplink ports but spanning tree takes 50 secs to failover so i want to enable rapid spanning treecan anyone let me know the relevant commands or post a link for a config guidei'm running c3560e-unive...
End-of-Life Milestones and Dates for the Cisco Catalyst 3560 IOS Advanced IP Services Feature SetI can't seem to find what the EOD life is for 3560I have WS-C3560-24TS-S 12.2(37)SE1and WS-C3560-24TS-E c3560-advipservicesk9-mz.122-25.SEB3
Hello all,I have a question regarding the combination of etherchannel and stp.My goal is to have four 3560G Switches connected in a ring, with 2GBit/s links between the neighbouring switches. I have connected the switches by channeling two 1GBit/s li...
I would like to lockdown our seperate vlans. Right now any vlan can ping any vlan and any host within... so obviously this is not a regular vlan configuration.thanks.
Hi I have two sites one is configured with:router eigrp 2 redistribute static network 99.0.0.0 no auto-summary no eigrp log-neighbor-changesThe other end is not configured with EIGRP. The below ip address is of the swtich without eigrp configured. Co...
Do I have to be running BGP for MSDP to work?This link says BGP is the pre-requisite.http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfmsdp_ps1835_TSD_Products_Configuration_Guide_Chapter.htmlAny thoughts ?
am loking for configuration for the 5020. Maybe a sample configuration. When I turn the box on I am beinga sked for an admin password.
What are the possible causes for this syslog message?PWRCYCLE Card in module 3, is being power-cycled off (Module not respondingto Keep Alive polling)Over the past few months, I have seen this message pop up now and then on different 6509 access swit...
I want to apply rate-limit or service-policy to an interface at 00.00 and to revert back at 07.00 everyday.What are possible solutions?Thank you.
Resolved! Verification on what I'm seeing with nat
All,I have to nat a complete subnet to something on my network. Currently, the company that we've acquired is on the 192.168.1.0/24 subnet, and we have devices on that subnet. I'll need to nat them to something else.What I've noticed is that if I do ...
Hello.I need to move a number of switches from VTP client to transparent in an attempt to gain control of my STP domain as the aim is to delete vlans from the switches that are not required.As I change the first switch to transparent (without deletin...
Hi,there is no log generating for TACACS+ Administration in ACS. ACS Version: 4.1.1.23Router Config:aaa authentication login default group tacacs+ localaaa authentication login no_tacacs local enableaaa authentication enable default group tacacs+ ena...
Problem:I am having problems geting the two interfaces to comunicate with each other. I can ping my Linksys Router from the outside interface of the firewall, but I am unable to do this from the inside interface. Also I heard that I need ACL's. What ...
