Switching

Hi...Whenever I telnet to the switch that my PC is connected to and type sho arp I get all the IP addresses of PCs connected to the switch while the hardware address is the same for all of them.How can I get the mac addresses of the PCs connected to ...

hello, I am looking for a low-end Cisco router that is suitable for operating in a home network environment. I would like to be able to support at least 2 subnets so I think I need 2 ethernet interfaces with the router. Also, I would like to be able ...

I have a question about communication from one host with an inside source static to another host with an inside source static through the public address. For example, I have a workstation with a 10.x.x address that has a public static of 199.190.x.x ...

Hello,I am very very new to Cisco IOS.So was this question.1.How to set up 2950-24-SI swith for a teaming I thought the following cong. worksSwitch_A> enable Switch_A#configure terminal Switch_A#set port channel 0/0 -7 10 {desirable} Switc...

I am used of using the Cat5 cabling on my working environment and now they want to move to using the Category 6 (1000Base-T) cable. Could someone show me on how could I do the CrossOver, Straight, RollOver cabling Pin-assingment on a Cat6 cable using...

Can someone please point me to where I can download the GUI for configuring Cisco-831 router?Thanks.

Hello,Sorry for cross-posting with the LAN switching and routing forums but I've realised only now that perhaps this is the right forum.We are planning o build a switched network using 3750G-24TS-S1U switches.Reading through the documentation I have ...

I have a customer with a 1710 router that has 1 remote site that VPN's in and runs a dos app locally that accesses data at the host site.Would changing the packet size in the router have any effect on the speed of the connection? File transfers are ...

first off i'm a newb so take it easy on meI just got a 1720 + wic 1-enet online along with a 2924i want to hook my cable modem up to the 1720 via wic 1-enet then the FA on that goes to the 2924 then to the rest of the computersThen get VLAN's made an...

I'm currently having the same problem on a couple of different sites running different hardware - one is a 1600, one is an 837. The issue is that the DHCP bindings table keeps filling up when it should not. On closer inspection it becomes evident tha...

Hi All CCIE'S and cisco champions...It's a basic question about IP but i don't know it and i am eager to know it..........Please help me out.....I have some data to share with you and then i have some confusions that i like to ask.I captured the pack...

I have 2610XM. I have configured register value to 0x101 for bext reload into RxBoot mode(Mini IOS), but it did'nt work on 2610XM, it work successfully on Cisco 2522, Why this, Is there any other register value for 2610XM to boot into RxBoot mode.Ple...

I posted this in the VPN Section some days ago. Maybe anyone here can help?We are terminating an VPN (for CISCO VPN Client) on PIX515.The Adresspool for the VPN is part of the ethernet1 (inside) pool and is not translated "nat (inside) 0 ...". The in...

Hi,I was able to borrow a 2610 that has 1 Ethernet, 1 aux and 1 serial port. I want to practice routing on the two interfaces -- serial and Ethernet and I want to do this at home. The ethernet side is easy but what cable and/or special configura...

Hi..We use cisco 2950 switches in several locations at our campus. All of them are locked up in cabinets. Some of these cabinets are located 2 to 3 meters away from clerks and receptionists working in an old building with no rooms designed to enclose...