Hi in Switch C93180YC-EXBy IOS 10.3(4a)For config netflow active and inactiove timeout have only on exporter Export Version 9Sequence number 1059486Data template timeout 60 secondsAny config active or inactive flow time out in this nexus????
Hi,can someone please advise why I need line 4 of below Acl? I understand we use established when we want to allow the response to the connection initiated from the internal network but on line 3 we allow ssh from any source to any destination alread...
Hi,I am getting the following error when trying to ping from PC to server can you please help me regarding this"ping request could not find server please check the name" in cisco packet tracker.I am here with providing my file.Thanks in advance.Kavya...
Problem Description:I am encountering an issue with the "set ip default next-hop" command on my n3k-c3064pq-10ge device.Device Information:Model: n3k-c3064pq-10geSoftware:BIOS: version 5.0.0NXOS: version 9.3(13)Configuration Attempt:I am attempting t...
Hello, this is most likely a firewall problem but I wanted to ask here before I go that route.I have 2 locations that are connected with the same fiber run. The primary site has an MX250, and 3 stacks of 2960x switches each with 3-4 switches in the s...
Hello,I'm trying to figure out why Avaya Phones and PC's are showing up as both statically and dynamically learned. We do not have any mac addresses statically configured. Here is the output of a few ports.Cisco9300# show mac address-table int Gi8/0/...
Hello Community!I'm new here. So be patient with me Im interested in the Cisco Catalyst C1300-16P-4X switches.Im want so build an Stack with two of them.My Question:How do I build a Stack with them on the CLI? The Official Guids are not so helpful.An...
I have Configured the 802.1x Configuration in WS-C2960X-24TS-LL Switch Globally. when i test the aaa test it was successful. but when i tried to configure in the Interface the authentication was not happening. so can you please help to configure the ...
Hey, i am working on a project And I have problems with my DHCP server. I don't remember how it came about. Hence I am asking here. I don't understand why my laptops at the bottom are not getting ip? Anyone who can help me. Packet tracer + Network di...
Hi thereHas anybody by chance still the latest firmware for the small business switch SLM248G? Since it's EOS it's not anymore available in the official database...Thank you very much for checking.
Hi,we are facinf and issue with ping from access to corecore management vlan 98 192.168.98.1 255.255.255.0vlan 103 192.168.103.1 255.255.255.0trunk port enabled for vlan 103able to ping access switchAccess switch management vlan 192.168.103.137 255.2...
Hello Bro,I am looking at the rack mount information about 9200CX, but could not find the clearance it may require to dissipate the heat from the switch. Does anybody share if the switches can be stacked tightly one on top of the other?Much appreciat...
hi all,we have a topology without any redundant link. Every access switch is directly connected with the core switch, and it's a port-channel between access switch and the core. RSTP runs on switches by default, and we do not explicitly configure the...
Hello all,20+ years ago I used debug all the time, however not so much so in the last decade. Seems like last time I called TAC on the 3850 debug command they gave me some silly answer that debug was a Cisco TAC command. WFIW All the Cisco.com debug...
Hi,
Do you have been happen this logging show that, and there are none any effect to our netwoek bunisness.
im client 'chasfs' has taken 332 msec (runtime: 332 msec) to process a 'stack chasfs fd' messageMar 28 23:25:32.568: %IOSXE_INFRA-6-PROCPATH_C...
