Activity in Technology and Support
How to extract the last 6 months logs in MX84
no syslog any thing configured but some how need to extract or check the logs for security purpose any leads?MX84 --> MX 18.107.10 versionfirewall forwards logs
Resolved! ISE - user can not change password if expire
We're running Cisco ISE version 3.5, patch 3,and we've joined it to our Active Directory domain controller.We ran into an issue where if a user's password expires,they can't change it while connected via 802.1X.Has anyone dealt with this? How can we ...
What security setup would you recommend for a small local service site
Hi everyone,I’m working with small local service businesses that use WordPress websites, and I’m trying to better understand what a sensible security setup looks like when the business doesn’t have a dedicated IT or security team.A typical site might...
Co-Term Licensing Help: MX65 to MX68 but MR36 Replacement on backorder
We are a nonprofit replacing an older Meraki deployment through the Cisco/TechSoup donation program and I'm trying to determine the correct licensing sequence.Current co-term organization:- MX65, Enterprise licensing- Two MR33 APs- Existing licensing...
Allowing specific Ip address from VLAN with extended ACL
Hello everyone,I'm currently continuing my Extended ACL lab, and I have a question.How can I allow a specific IP address within a VLAN 30 (IP address: 192.168.30.10) to access another VLAN without allowing that other VLAN to access the specific IP in...
Problem ACL with SYSLOG server
Hi ALL,I have issues in access list. I configure access list in switch for syslog massage with port 1514 and set in VLAN outbound but not matchIOS version (X86_64BI_LINUX_L2-ADVENTERPRISEK9-M), Version 17.12.1Extended IP access list SNMP&&AAA&&SSH10 ...
How to Set Speaker Mode as the Default Camera Mode Instead of Dynamic
We have a Cisco Room Kit codec, and we would like Speaker Mode to be selected as the default camera mode without requiring any manual intervention.Currently, Dynamic Mode is automatically selected by default under the Camera Control options on the To...
Failure to recover during an IPsec switchover
Traffic from Server-1 to Server-3 is encrypted using a policy-based IPsec tunnel between Router-1 and Router-3.Router-1 and Router-2 are configured in a redundant setup and share the same VPN endpoint address.The system is configured so that when Rou...
Which router ? C8300-1N1S-6T or C8235-E-G2
Hi GuysI need to purchase 2 routers for a large site, the site will have up to a 1Gig MPLS linked to each of the routers.I was looking at the C8300-1N1S-6T, however the later series has appeared to come out, the alternative model was the C8235-E-G2Th...
Port-Channel don't come up after firmware upgrade on C1300-24FP-4G
Hello,I upgraded the firmware of my Cisco Catalyst 1300-24FP-4G switch from 4.0.0.91 to 4.1.9.85. Previously, on the old version, the port-channel was working fine with Cisco Catalyst 1300-24XS (version 4.1.3.36).Interfaces detail which were bundled ...
Resolved! Re: Wireless Controller 9800 RP port
Hey all,Just wanted to confirm that this also works with the new Cisco WLC 9800H RP using a 1G GLC-SX-MMD SFPAfter spending long time on tshoot, I found that the RP port would not work with a 10G-SR SFP, Once I replaced it with the 1G GLC-SX-MMD, the...
AMA - 2026 IOS XE Software Security Hardening update
Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
ise troobleshoot
Hello, I need some help with a Cisco ISE issue.802.1X authentication works normally, but when a users AD password expires, the password change fails with the message unable to contact the domain controller.The Enable Password Change and Allow Passwo...
Discovery issue on Fabric Interconnect 6536 with Chassis 5108
We have the following connectedFabric Interconnect 6536 (UCS-FI-6536), 5108 Chassis with 2x IOM 2408 (UCS-IOM-2408 V03).We've cabled them with 100G QSFP28 to 4x25G SFP28 AOC 5M (NWP-QF-100G-S4-AOC-05-C)We've configured port as server port on initial ...
UCS C240 CPU without frame
Need to replace a CPU on a UCS C240 M4 server as per https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C240M4/install/C240M4/replace.html#45480. However, the CPU that was delivered doesn't have the CPU plastic frame. So I'm not able to...
| User | Helpful Count |
|---|---|
| 91 | |
| 51 | |
| 38 | |
| 36 | |
| 35 |
