Activity in Technology and Support
help with configuring two ethernet ports on a cisco 4451x/K9 router
I need help with configuring GigabitEthernet0/0/2 and GigabitEthernet0/0/3 on my cisco 4451x and all Gemini has done is just give commands from old cisco 7200s and earlier and kept giving random commands that didnt work please help
CSCvn31571 - duplicate VLAN-ID on FTD
Is this CSCvn31571 a bug or by design that I can't have duplicate VLAN-ID on 2 or more sub-interface?
Meraki Lab Not Spinning up
Hi team,Hope you're doing well. I wanted to flag an issue I ran into while trying to spin up the Meraki sandbox.The environment failed to launch in Torque, with this message:I tried to spin it up three times this afternoon (June 14, 2026) and all thr...
Cisco WLC 9800-CL WebAuth Pending problem with Fortinac Captive Portal
Hello,I successfully integrated Fortinac-F on my Cisco WLC 9800-CL. When I connect to the SSID, the NAC successfully moves the subscription from the isolation VLAN to the guest VLAN and accesses the internet. However, the web authentication status on...
My "A" record is incorrect in OpenDNS but correct in other DNS servers
My "A" record for comimprovementsinc.com is incorrect in OpenDNS but correct in all other public DNS servers queried. My DNS is housed at BlueHost and the "A" record was updated in my DNS server at BlueHost greater than 72 hours ago.See the attached...
Top 2-3 useful Meraki Workflows
I’m evaluating Meraki for a wireless deployment and wanted to understand from a practical standpoint — what are the top 2–3 workflows customers genuinely find most useful day-to-day?In particular, which workflows actually simplify operations at scale...
Checking the Number of Packets Matched by PBR
I have configured a PBR to change the next-hop destination (set ip next-hop).I believe the `show route-map` command should allow me to check the number of packets matched by the PBR, but the match counter remained at 0. Does this mean the PBR is not ...
Error API Response Received from Finesse for Silent Agent Monitoring
Hello,We are encountering an issue with a specific supervisor in UCCX when attempting to perform silent monitoring. The Finesse API is returning the following error:FinesseController::MakeSilentMonitorCallCommand FailedCisco TAC has reviewed the UCCX...
Resolved! Re: Cisco 8851 phone keeps trying to register
I just deployed my CUCM 15 in production, and everything goes well until I connect the IP phones for testing. Unfortunately, I can't see the phones in CUCM, even though they are receiving IP addresses from DHCP as well as CUCM's own IP addresses (PUB...
Resolved! IOS-XE upgrade discussion - "install" mode vs. "request platform"
Hello all,In terms of doing IOS-XE software upgrades, there are 2 ways to do it - the install mode way, or the request platform way. @Leo Laohoo has written some great guides for upgrading ISR models with request platform and upgrading Cat 9k models ...
Resolved! OSPF Discontigous Area 0
Good Day Outliers!I am doing a little lab here, after reading the Discontigous section in the CCNP/CCIE book for ENCOR (Official Cert Guide). The book states:Fair enough. But then it says:The book then states the 3 essential rules:So I was curious if...
ISE Admin & Guest Portal certificate renewal.
Hi,I have a change to renew the Guest Wifi sponsor portal certificate & Admin certificate in ISE. Please share the complete steps to do the certificate renewal.We have 2 PAN & 3 PSN nodes. I am little bit confused with the current certificates being ...
Connectivity issue between cisco Prime and cisco controller 9800
We have installed Prime on our system and are trying to add our controller to Prime for SNMP trap monitoring. However, Prime is showing a Ping Failed error when we attempt to add the controller.The controller is able to successfully ping the Prime se...
UCCX no Rignigng
We have CUBE-SIP CUCM-UCCX IVR- agentMy issue tested from internal or external, found it the same.When calling from CUCM to UCCX, the caller can hear the IVR, and when selecting the agent, we cannot hear the ringing but silent till the agent answers,...
Data Export with Emergency Responder 12.5(1)SU9
I am trying the Data Export feature with CER 12.5(1)SU9 but it is not working.When I run the export command, it just hangs.I’ve tried it on a couple different deployments, and get the same results.Wondering if I am doing something wrong, or it just d...
| User | Helpful Count |
|---|---|
| 91 | |
| 86 | |
| 53 | |
| 50 | |
| 47 |
