Activity in Technology and Support
WRVS4400N total waste of money ?
I have bought the WRVS4400N hoping for a good router with VPN support. What a disappointment...Here are the issues I'm facing, after searching for answers on the Internet I have come to realized I'm not the only one with those.I hope Cisco will liste...
Install CUCM device package
Hello,We have two CUCM VM machines "Subscriber & Publisher" version 12.5.1.18901-1 and need to install device package "cmterm-devicepack12.5.1.22212-1.cop" to adding 9800 phones. Appreciate your support to know to install it and should installed it a...
Custom Traffic Shaping Rules on the MX for Dell Update is Not Taking Effect
We have this traffic shaping rule configured on the MX under Security & SD-WAN > SDWAN and Traffic Shaping where we created a custom expression for downloads.dell.com traffic and limited the upload and download bandwidth to 1Mbps. But a couple of day...
10G WAN Connectivity on MX105
I have an MX105 deployed at one of my branch locations that has a SMF (Single Mode Fiber) connection to my main office building. I'm attempting to build 10G connectivity across that SMF, but have been unsuccessful to establish link. Summary of my s...
Unable to access router when uplink goes down
This seems like a weird one to meWe have the following setup WAN1 __________ ROUTER 1 __________ internet 1 /MX 1- \ WAN 2 __________ ROUTER 2 _________ internet 2during normal operation - from the inter...
MX to Azure site-site VPN using IKEv2
We're looking into setting up a VPN from our Meraki MX device to our Azure environment, however we have seen that some issues may arise when it comes to using IKEv2. does anyone have some documentation on this kind of VPN being setup?Thank you!
VPN Clients and secure key usb
Hi all,I successfully configured the Meraki VPN (on MERAKI MX100) with a shared security key and email/password for each user and native Windows client. But would it be possible to increase security using a USB authentication key or Microsoft Authent...
FPR1120 7.6.2.1-3 (FDM upgrade failed)
Hi allMy device is working in FDM mode without FMC. it is version 6.2.1-3. Last week, I planned to upgrade to the version 7.6.4-69 recommended by Cisco, but unfortunately, there were errors during the upgrade process. By checking the upgrade status i...
Why Should I be learning SD-WAN in the era of AI?
It's been quite a few days since I started learning SD-WAN through YouTube. And as I move forward, I have this question from others: "Why are you learning SD-WAN in the era of AI?" Is it even necessary?I kept searching and found a few answers... Plea...
Nexus Dashboard Multisite Setup
I have created multisite setup and i see router being exchanged and remote sites leafs are populated. I see that i cannot ping from one site to another. I just want to know if this is due to some limitation related to sandbox or something wrong with ...
LACP timers on DNAC appliance (ISSU upgrade on Nexus switches)
Hello,We want to upgrade our customer's Nexus 9300 switches using ISSU but according to the Cisco documentation LACP timers set to fast rate is not supported for ISSU upgrades. The Cisco documentation for Catalyst Center Appliance installation says t...
Welcome to Cisco IQ
Your Cisco Support purchase unlocks AI-driven and expert-led support for greater uptime, performance, and resilience. Now with Cisco IQ, a unified, AI-powered digital interface, you will experience hyper-personalized, proactive, and predictive suppor...
How the Trusted List IPs is populated on Cisco Unified Border Element
The well-known Trusted List on Cisco Unified Border Element CUBE helps to prevent Toll Fraud. The ip address trusted list command, configured under voice service voip, is used to define which IP addresses are allowed to send incoming calls. But keep ...
Should I use a configuration that utilizes HSRP tracks?
We have configured the router’s LAN side for redundancy using HSRP and the WAN side using BGP.If the WAN interface goes down, I believe outbound traffic will follow the path FW#1 → L2SW#1 → Router#1 → Router#2 → L3SW#2, and return traffic will follow...
DHCP Packets in Wireshark
Is it possible to capture all the DHCP Packets in one or even capture them in different. I'm successful in capturing the first five packets (till release) in wireshark while working in eve-ng to learn DHCP. But I don't get how to generate the other 3...
| User | Helpful Count |
|---|---|
| 62 | |
| 58 | |
| 52 | |
| 49 | |
| 46 |
