Can all the ports be enabled to "answer calls" and "message notifications" in the same time? I currently have 16 VM ports.Thanks,
Can all the ports be enabled to "answer calls" and "message notifications" in the same time? I currently have 16 VM ports.Thanks,
Thanks in advance for your responses, just wondering if anyone had encountered any issues when running a Tandberg/Polycom endpoint codec in the LAN to access a VCS / gatekeeper across a FWSM (cat 6500) . I'm just having issues in which a video is los...
I was able to get a translation to work on all inbound numbers, but I have a single fax on fxs0/1/0 that is getting lost in that translation. Can someone assist in a translation that would see the fax number (555)555-1112 and point it off to the fxs...
I'm running CME 4.1 with a FXO and FXS ports.The internal telephony network is running fine, my problem comes when trying to make a call from the PSTN to an anaolgue phone connected to the FXS port.I can make outbound calls from the analogue phone, I...
hai everyone,whether they could connect the vic-2xs in a fax machine?
Hi everyone,I've configured two FXO ports attached to two routers in different cities,I have some ip phones registered in CME too,the problem is that when with iphones dial some analog phones that connected through FXO to PBX the sound volume is very...
Hello,we try to setup a sip account with cucme 8.0.it seems to work good but supplementary-service is not working and codec is a problem.we cannot set call-forward all with sip.we use g711 alaw codec for sip and with this codec it is not possible to ...
When trying to upgrade a CTS-1000, it fails and gives the message in the logs "ERROR: Codec firmware upgrade is disabled".Every other unit in our network upgrades OK. The Cisco documentation I have seen says "Contact TAC for assistance". Anyone abl...
If we have a telepresence unit connected to our MPLS provider (Telco A), and we're interested in having a conference with an outside company on a different provider (Telco B), what are some options to make this happen?Is it possible to have dual telc...
Are third-party Telepresence endpoints interoperable with CTMS?Anyone tried using any Polycom/Tandberg Telepresence endpoints with CTMS without having to interface through CUVC?
Hello,We have a Video SIP Endpoint registered in CUCM 6.X. For some reason we are only getting one-way video (CUVA to SIP). The SIP endpoint is sending a video stream, but CUVA is not receiving it...Does anyone have success making a video call betw...
hii have CTMS v1.6.0.0-108 when i change the Qos to setting to i want, it go back to AF11 for both TP and CUVC after i hit apply !!is this a bug,, is there any workaround !!
Hi everyonemy connection likeTanberg1--------IP--------Gatekeeper---------CUCM----------2811-----------PRI----------PSTN----------Tanberg22811 use most recent IOS 12.4(24)T3the Tanberg1 doesn't have any BRI/PRI on it, IP only, it register with gateke...
If I have a TelePresence Segment and a SD endpoint - what would be the call flow in setting up an ad-hoc or scheduled video conference between the two endpoints?What is the role of the following components:CUCMCTMSCUVCAlso, which device is produced b...
Our voicemail appears to be down for the users.Unity Call handlers are working, and when you call in you can leave a message.But, when that user checks their voicemail, after entering their PIN, they get dead air.Also, the users are not recieving the...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-02-2024 05:48 AM | ||
08-01-2024 12:01 AM | ||
07-30-2024 03:24 PM | ||
07-29-2024 10:10 AM | ||
07-29-2024 12:01 AM |