Unified Communications Infrastructure

Problem with TSP 7.0(2.2)

Hi,i’ve encountered an issue regarding the registration of TSP drivers 7.0(2.2) installed in (WinSrv 2003 SP2) and CUCM 7.0.2.10000-18 The TSP drivers have been downloaded from the related CUCM plug-in page.The configuration has been done inserting s...

Hiding the translation !

Hi all experts.I am trying this in lab for knowledge purpose so please guide me. I am using cucm 7Lets say i have 2 locations. Location A and location B. B contains DID range of 8562000 - 8562999. Now when i dial 2000 from location A, it should trans...

Looking for a shopping list of components

We have a diverse environment today containing the following:Corporate office with around 300 users on a old Nortel switchLess than 10 remote offices running Cisco CME ranging from 5-125 users eachOld version of Cisco Unity supporting all of the abov...

3 X 3 Upgrade ESW

I'm planning a CMBE upgrade from 7.X to 8.5 for a customer without UCSS using 3X3 upgrade. The part numbers that I'm using are UPG-BE5K-ENH, UPG-BE5K-VMB2A, UCSS-BE-KENH-3-1 and UCSS-BE-KVMA-3-1. I assume these are the correct part numbers. What I a...

9900 Phone + WebEx Meeting Center

Hi Community,a client of our own is very excited about the 9900er Phones. From scratch, the can start a point-to-point video conference, that sounds good.Now, he wants wo use WebEx Meeting Center, additionally on the phones. At this point, I could on...

Resolved! Which route pattern ? 20! or 20xx ?

Hi all experts.If i configure following 2 route patterns1) 20!2) 20XXAnd dial 2001, which one is the best match ?

Callmanager routing logic !

Hi all experts.I am trying to understand call routing logic of cucm.I created 2 route patterns in cucm 72!2XXX (with urgent priority)Now when i dialed 2001, i had to wait 15 seconds. The call wasnt routed as i expected. I opened up Troubleshooting ci...

cisco ip phone config help

Hi ,I have did my best , but still the cisco ip phone 7931,7945 and others doesn`t accept the configuration i did on the cisco cme - despite i reset the phones , the cme router, and i unplugged the network cable from the phones.the configuration:Rout...

Resolved! Change Unity 5.x Partner Server - Can't Remove Exch 2003 Mgmt Tools

I'm trying to change my partner Exchange server to Exchange 2010. Part of the procedure states to remove the 2003 management tools and install ExchangeMapiCdo. I cannot remove the 2003 tools. The installer fails with error "an unexpected error occurr...

Session ID

Hi Guys,I have an issue with my script. I have web integration between CUCCX and a web server. I need to pass on the session ID to web server. PLease advise how to achive it.Thanks for helping

CUCM Upgrade

I am currently running CUCM 7.1.5 on a 7825H2, with 72GB disk and 2GB of memory and getting ready to upgrade to 8.5.1 on a C210 Virtual server. I know I need to upgrade to 8.5.1 first, but it recommends upgrading the disks to 146 for better performan...

cisco ip phone ringtones

Hi,Ina company which uses cisco call manager express with ip phones 7931, 7945 ,7975, 7911,7962…….Pleasecan you help me to install for the ip phones different ringtones and then theemployee will have the option to chooseanyringtone he needs.when i cl...

CUPC Login Failed

We just upgraded CUPS from 7.0 to 8.0. After the upgrade, the new 8.0 CUPC is unable to login, however the older 7.0 CUPC is still able to log in.I found this in the CUPC log:2010-10-26 08:25:56,348 ERROR [10] [Cisco.Uc.Clients.Common.WpfServicesClie...

2951 as voice gateway

Does anyone have a link or wizard that could assist with guiding on providing the number of voice cards, PVDMs and DSP resources to accommodate:4-pri's and 4-FXO's? Along with the required configurations / dail-peers etc....Thanks

CUCM with Microsoft Unified Messaging Call Transfer issue

Hi,I've a customer using CUCM with Microsoft Unified Messaging. When IP Phone user sets Call Forward all to voice-mail, the transferred calls never reach his voice-mail box. The caller gets dead air. Direct calls to the extension does get forwarded t...

Unified Communications Infrastructure

Forum Posts

Problem with TSP 7.0(2.2)

Hiding the translation !

Looking for a shopping list of components

3 X 3 Upgrade ESW

9900 Phone + WebEx Meeting Center

Resolved! Which route pattern ? 20! or 20xx ?

Callmanager routing logic !

cisco ip phone config help

Resolved! Change Unity 5.x Partner Server - Can't Remove Exch 2003 Mgmt Tools

Session ID

CUCM Upgrade

cisco ip phone ringtones

CUPC Login Failed

2951 as voice gateway

CUCM with Microsoft Unified Messaging Call Transfer issue

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

CUCM 12.0 to 12.5 PCD migration

CUCM Constantly Disconnecting TCP Socket

"Service Manager is currently busy" After Restarting Cisco XCP Router

Secure SIP integration between CUCM and IM&P...

Monitoring/alerting for issues with Unified Messaging and Speechview

Enterprise Mobility Management (EMM) Alternative Configuration Fields

MRA Expressway E complaining about RMS License "Out of Compliance"

Oauth access tokens

How integrate two CUP server with different domain ?..

CuCM SQL table for shared lines