So...I need to upgrade two 5108 Chassis / B200 M2 and I have some doubts.1st- Which version should I use? I took a look at the https://ucshcltool.cloudapps.cisco.com/public/ but I am not sure abou it. 2nd- How to performe the upgrade, I mean ... I kn...
Forum Posts
Hi, ESXi is installed on a blade with a service profile that has no vHBAs. If the vHBAs are added to the service profile, does ESXi need to be re-installed when that service profile is re-applied to the blade? Thank you,
Resolved! 6248UP Expansion Module Question
Does anyone know if the ports in the Expansion Module for the 6248UP (pn UCS-FI-E16UP=) can be used for same personality types as the fixed ports? We need ports for the uplink to the core and downlink to the chassis. We are receiving differing infor...
Hi I am new to Cisco UCS product. we have bought a Cisco UCS 5108 with 4 blades and 2 FIs. now i am implementing it. Cabling is finished and i have all connectivities established to storage and network. now i am going to create a service profile and ...
Resolved! Cisco UCE-e configuration with sub-interfaces /router on a stick (ISR4351) SVI and without SVI
Hello All, I have a Cisco UCE-E 140D and a ISR4351, however, I am trying to configure the uc1/0/0 and uc1/0/1 for trunking through the subinterfaces of the router. I am running vmware 6.5. For example , I have subinterface on the router gi0/0/1.90...
Hi Guys, Need some help with UCS central backup job. I have created one time backup job for a ucs domain. Now i am trying to figure it out how to delete that backup job, but could not find it. This backup failure keeps on alerting a major alert. ...
Hi, I'm getting this Minor fault on my primary FI : Disk usage for partition bootflash on fabric interconnect A exceeded 70% Wanted to know, what can I delete from it, except .bin files. Is there some "garbage" files that I can delete from it ? t...
All, Is there a method for converting an existing single card flex flash to RAID 1 without losing data on the existing flexflash card. Blades were originally purchased and configured with a single FlexFlash SD card. Now there is a desire to add ...
Hello,we are using the following setup:- B200 M5 Blade Server- Firmware Server: 3.2(3a)- Firmware UCSM: 3.2(3a)The Boot Order looks like this: After assigning the service profile with those settings and booting the server, the UCSM shows a different ...
Hello, My question is about a a NIM E-Series NCE which doesn't boot a VMWare hypervisor. First of all, a few things which look abnormal to me.On the NIM E-Series NCE, I get this: EN140N-FOC22022YY0# scope chassis EN140N-FOC22022YY0 /chassis # sho...
Hello,My question is about connecting a NIM E-Series NCE to a PC via a console cable and the management port. NIM E-SERIES NCE Management port (port 2) (see image 1 below) | | Console cable (see image 2 below) | | PC The settings for the connection...
Hi All, Good Day, Have anyone had any experiences with the newly released patch 3.0(4d) for UCS firmware's yet? I have been trying to perform some research on its stability to be run on production environment.
All,We have a Flexpod system with a UCS 5108 chassis, B200-M5 blades, 6248 FI, Nexus 9K, and NetApp storage. It is connected and configured using the CVD document; however, when exporting VMs from ESX, the file transfer is horribly slow and times out...
I was wondering what others have been doing over the years when implementing multiple FI domains into a storage fabric (MDS) and the vSAN management. You really have 2 options:Option 1 --> Each FI Domain has a distinct vSAN and the MDS to storage arr...
Hi is it possible to delete som lines from the audit or event logs in UCS central ? i have a customer that need to know if it possible. /Kristofer
