Unified Computing System Discussions

ESXi 6.5 fails to see the LUN on the SAN UCS mini

UCSmini 5180 (M4)Connection FCOE unifield uplink Adapter 1340, 1380 Fw 4.1 (3a)Driver 1.6.0.28 i'm not sure driver version for ESXI 6.5 is correct. Log on ESXi6.52017-09-13T10:46:16.840Z cpu24:396802)WARNING: vmw_psp_rr: psp_rrSelectPathToActivate:11...

Cisco UCS C220 M4 standalone with VIC 1227 not connecting

I have two Cisco UCS C220 M4 standalone servers with VIC 1227 in the mLOM slots. There is light coming out of the SFPs of the same type that are installed on both ends but the systems are not connecting to the Cisco 6500 switch. The BIOS on the ser...

run HUU with CLI

Hi! Experts: Is there anybody know if it is possible to run HUU with CLI?

reset deviceID enumeration on Cisco 12G SAS Modular Raid Controller

Trying to find a way to truly wipe the config of modular RAID HBA, it seems to retain the "Device ID" of drives that have been inserted in NVRAM. The storage adapter utility you access during POST has a reset which doesn't work, CIMC /chassis/stora...

UCS VLAN and multicast policy

Hi Do we need to mention the Multicast policy with VLANs that are created with UCS. The VLANS are configured to use with Hyper V 2016 environment and using for HV Live Migration, HV Cluster and for VMs. Thanks in advance

Resolved! Only one vHBA is show up...

I put into two identical brand new B200 M4 blades today to a 5108 chassis. The UCS version is 3.1(1h). The blades were discovered and have the necessary profile associated. Now I got major faults about vNICs and vHBA. As showing in attached screensho...

Resolved! Different UCSM and Blade Versions

We have a mix of B200 M3 and B200 M4 servers a total of 20+ Blades running currently on 2.2(5b) UCSM Version and with a recent Infosec update we need to fix some Vulnerabilities with Vmware and wanted to know if can just upgrade the Server Blades to ...

Remove Esxi from ucs

Hi all, I have a use c240m with esxi, and I need to remove it and install centos. Every time a try to install the centos it keep booting the esxi. thanks.

Resolved! 6248up to a C220 M5 with 1387 mLOM

Hi,I'm considering attaching a new UCS C220 M5 server with a 1387 VIC adapter to an existing 6248UP FI pair.Since the 1387 adapter is 40 Gbps QSFP+ and the 6248UP is 10 Gbps SFP I assume I'll have to use something like a SFP-4SFP10G-CU3M, 40GBASE-CR4...

Can I connect Server (apart from Cisco) to Fabric Interconnect ?

Hello,I have a question. I want to connect any other server apart from cisco to connect directly on Fabri Interconnect. Is there any way I can achive this?-Amit

Resolved! vHBA limits on M3 blade with VIC 1240

Hello,I have an UCS environment with FI 8324 and B200-M3 blades and VIC1240 cards. The VIC1240 data sheet says support for up to 255 virtual interfaces. But the service profile association fails when there are more than 32 vHBA's created. Is there ...

Resolved! Raid. Firmware failed validation.

Hi all.I get the nex error during boot-up. Please help.

How traffic flows when more than one uplink port channel per FI came into picture

Hello Experts,I need your help in clarifying one doubt related to ethernet uplink port channel.as a standard design, I have 2 ethernet uplink port channels, one on each FI with 2 ports in there.All the vlans trunk on the northbound switch with LACP c...

Resolved! Removing uplinks from IOM.

Hi, We are currently running above our licensing with 4 uplinks in IOM-1 and 2 in IOM-2. We wish to fix this by unplugging the 2 extra uplinks to remove the ETH_PORT_ACTIVATION_PKG error, hopefully without any disruptions.I've been searching around t...

switch ucs fi

hello, need your help \ recommendation , i want to connect our switche UCS FI as Switche Layer 3.if thare recommanded? there is 20 Interface Vlans.TNX