Hi,Is it possible to backup a configuration(All configuration) from a UCSM 2.0 and import it to UCSM 2.1 ?or do I have have to downgrade the firmware to 2.0 so that it will match the source and then import?Jibby
We are looking at upgrading our UCS system from 2.0(1m) to 2.0(5a). We have ESXi hosts that are currently doing iSCSI boot and as such, we have iSCSI vNICs attaching to LUNs on a SAN. We ran the duplicate IQN script and it came back with 4 entries:...
Hi,We are running UCS 1.3 on 6120XP FI, connected to EMC CX4-480, Fabric Switch DS220b with FOS v5.3.0(a).Need to upgrade UCS to 2.1.What is the minimum FOS version on DS220b required to upgrade UCS to 2.1?I dont see DS220b/Brocade 200e switches in a...
Dear forum users,We are planning to install XenServer on our Blade 200 M2.My question:1) During vHBA setting, it was asking what is the Adapter Policy (Linux, SRIOV, Solaris, VMware, VMwarePassThru, Windows, Default). So what is the policy i need to ...
HelloHaving an HA issue with a FI cluster and have not able to find much info.The error I get (in the subject) leads me the the below URL with 5 steps to check.http://www.cisco.com/en/US/docs/unified_computing/ucs/ts/faults/reference/2.0/UCS_SEMs.htm...
I would like to directly connect UCS6248 to storage, so the SAN switching mode is planned. In addition I have two rack servers and I would like to connect them to UCS6248 with FC in order to make access to storage. Is it possible or not? If yes, how ...
Hi Guys. I want to create a RSPAN session on the 1000v, i need to copy packets from a veth local interface and send the packets into a different flat L2 vlan, is this possible because i only see that 1000v can do local span and erspan?thanks
Hi,While configuring UCS Manager 2.0 to authenticate against an LDAP provider (Active Directory) I´m a bit unclear whether the "Attribute" field is required or not when the LDAP Provider is configured?According to the Configuration Guide page 137 it ...
Hi, I recently upgraded our 5548UP nexus switches from 5.1(3)N1(1a) to 5.2.1.N1.3. during the end of the upgrade (before rebooting) it says the following - ote: Micro-controller upgrade needs a power-cycle to take into effect.On success of micro-con...
Hi, we have a setup where we are connecting the UCS FIs to nexus 5548UP with layer3 modules. All layer 3 for the UCS domain will be handled by the n5ks. The n5ks are in a vpc domain and each FI is dual connected to both the n5ks. Now I will have to c...
I am working with a customer to configure HP System Information Manager 7.1 (SIM) to monitor their Cisco UCS Manager. The customer is looking to monitor the following:- CPU Utilization on manager, blades, servers, etc...- Memory utilization- Network ...
Hi, All:Can one connect an FCoE target directly to a Fabric Interconnect or a Nexus 5xxx FCF when in NPV mode and not connected to an FC switch for fabric services and still be able to have the initiator see the target and be able to provision storag...
Hi,In Internal LAN section, I have a port-channel with no members. When I try to delete it with GUI, I have an error "Port channel cannot be deleted". With CLI, I only can delete member, but I have no members.Thanks for help Stéphane
when I do this following on my FI, I am getting no info at allconnect adapter 1/3/1connectattach-flsadapter 1/2/1 (fls):2# vnic---- ---- ---- ------- -------vnic ecpu type state lif---- ---- ---- ------- -------23 1 fc active 1224 2 fc...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
