Hey, i have a weird issue in that i have 8 hosts, all configured correctly - but 1 host when i go to its KVM just says 'connecting Viewer' all the time. the other hosts are all good and i get the esx prompt screen, this affected host has no issues ...
Forum Posts
I have a C220 M5 which was installed with a UCS-MSTOR-M2 storage carrier and 2 2540GB SATA M.2s (UCS-M2-240GB). When booting with UEFI, I do not see the drives listed anywhere when entering the BIOS via F2. This includes when I check for available bo...
I cannot lohgin to ucsm. I rebooted my machine and now I cannot login. why am I getting this message?
Upgrading a cluster of 3 M4 UCS Blades and 1 M5 Blade. All VM's will vmotion without issue between the different type of blades within in the cluster, except for the newly upgraded vcenter 7.X VM. When I attempt to put the M5 blade (which hosts the...
Resolved! Change vCenter Credentials HyperFlex
Hi All,What is the best way to change the vCenter credential of our Cisco hyperflex environment. Do I have to reregister everything on the HX Dataplatform or is there any specific command to update the vCenter credentials.I will be very grateful for ...
I have an S3260 with factory installed firmware 4.0.1a. I tried to upgrade this to any 4.x.x using the UCSM, CIMC and the HUU but the CMC always fails to upgrade while all the other components could be upgraded successfully. Although the firmware dow...
I'm trying to find the DNS IPs, domain name and NTP IPs for my Supervisor appliance but having issues. Here's what I can see:Seems like no NTP sources are defined:[root@localhost etc]# ntpq -pNo association ID's returned[root@localhost etc]#Seems lik...
've got some B200 M4s and C220 M5s and all are running the Cisco TPM 2.0 (UCSX-TPM2-002) The modules are functioning fine and are reported correctly but don't appear to work with the new TPM Encryption feature in ESXi 7.0 U2. vCenter throws up a nice...
Hi Team, I tried to setup Intersight mode from initial configuration dialog. However, after erase-configuration from UCSM, mode selection was not shown up. UCSTEST-A(local-mgmt)# erase configurationAll UCS configurations will be erased and system wil...
Resolved! UCS chasis ,FI and server compability
Hi to all , ı am trying to search for the compability between B-series Servers,BladeChasiss and IOMs ,but i am not yet succesffull. I found the tool (https://ucshcltool.cloudapps.cisco.com/public/) for interoperability ,but cannot found what i am loo...
Hello Team, Trying to rename a FI via intersight site but there is no option for that. I guess, I need to reset them but I cannot issue the connect local-mgmt command, sais not available. Any help will be deeply appreciated.
Configure UCS M5 server hardware for TPM module.This procedure is written for situation when new TPM module UCSX-TPM2-002B is installed in UCS C220 M5 server which didn’t have TPM module before, so you may need to adapt this process to your particula...
Hello,i am trying to reconfigure the RAID's on a Cisco UCS C220 M4S and am stuck. Not sure at this point if it is even theoretically possible.We have one Cisco Server with the following RAID configuration, each of them has 2 Disks:VD 0 and 1 contains...
Resolved! Rollback Cisco UCS server firmware
Hi all,I have an inquiry about the server ucs-c series, I am preparing an update for firmware BIOS and CIMC, and I want to add the odds if the update doesn't work, could you have a procedure for a rollback thank you in advance.
The server went down while being in use and upon attempting to bring the server up, it will not discover. Any ideas or help? Blade will not discover, we have attempted a virtual reset through ssh and have also manually reseated the blade to attempt ...
