Hello, I have a whole bunch of tunnels configured via ASA5510. I can see all the active tunnels/count of active tunnels using: show vpn-sessiondb summary.My question is.. how do I find out if any of the tunnels are still being used or when they were ...
Forum Posts
I am using AnyConnect 4.6.01103 on Windows for the first time, but I receive that message, so I am unable to connect to the VPN. What should I do to fix it? Thanks
I have Windows 10 21H1 with an Intel AX200 WiFi adapter, and also AnyConnect version 4.9.06037 I noticed WiFi is very slow, download is about 26 Mbps and upload 48 Mbps. It should be several hundreds. My phone on the same network gets 435/95 (the int...
We currently have a PKI based IPSec Remote Access VPN running on an ASA. We need to switch the entire Trust Chain. During the migration window, we need to be able to support AnyConnect VPNs with either Trust Chains. I don't have a lab to test.My curr...
Hello, I need to use external windows DHCP server for address assignement for AnyConnect clients I found several guides how to make configuration. For instance : https://www.petenetlive.com/KB/Article/0001050https://integratingit.wordpress.com/2022/0...
Good Morning,Equipment: Firepower FTD1120 - V. 7.2.0-82I have a local network in 192.168.1.0/24 and a site-to-site between a network 10.100.29.0/24 and 10.100.30.0/24.I set up an Anyconnect VPN with a split tunneling of the network 192.168.1.0/24 so ...
Hi,for a while now the Anyconnect client on my MacBook pro refuses to run, I first noticed this issue when I upgraded to OSx Monterey. I have uninstalled and reinstalled it several times but this hasn't helped. I have attached a DART file. Any ass...
Resolved! DMVPN tunnel stuck at NHRP state
HI Experts and friends, We use DMVPN and Eigrp as routing protocols to Connect between sites. I am facing a peculiar issue. The dmvpn Hub router shows tunnel up for the spoke IP router but the spoke router is stuck in the NHRP state. Hub: WAN-RT-01#...
Given: An ASA5525 HA pair hosts an Anyconnect VPN. Anyconnect join time is normally two seconds.A failover event occurs unrelated to Anyconnect or its ports. All users maintain connectivity, but now freshly joining users join time is approximately on...
Hi Guys, I have been having some issues with site to site VPN .. Ok my topology goes like this Topology I have ospf running both internal Lan and point 2 point routers which has site 2 site VPN connect established successfully now for fail ov...
Hi. ASA 5525 Anyconnect user login period is now about 1 minute. Usually it takes a couple seconds.Last night a new device was installed that connects to the ASA5525 on one end, and a vendor tunnel on the other end. I cannot log into the new device.M...
I've run into a problem with a working DMVPN setup, where I need to move the external (DMVPN source interface) from the global table into the same VRF as the tunnel.Prior to adding the external into the VRF the tunnel was up and passing traffic.When ...
We have AnyConnect 4.10.05111 installed and use Okta to connect with SAMLAnyConnect is set to use the embedded browser but it appears an update to Microsoft Edge WebView2 Runtime 109.0.1518.52 broke the Okta login page from displaying properlyWe have...
Hello.I'm troubleshooting an ASA 5525 to CSR1000V failed tunnel turn-on. I notice that port 500 is being used, which means that NAT-T is not being used. What are the commands inside the VPN configuration enables NAT-T so that it will use UDP port 450...
New L2L vpn, how does 1 point first find the remote public address,?The 2 public endpoints must find eachother over the www, public IP addresses are assigned to new www endpoints all the time.So, how does a new route establish in the first place?Than...
