VPN

We're using a pair of VPN-3030's for remote access, specifically client-to-site connection. I need to see the user name for a connection that was assigned a certain address about 6 hours ago. Unfortunately, the event log will only show me an hour wor...

hi, I'm kindda new in this field. I've to setup a small VPN between 2 location. I'm not sure about the hardware & configurations needed. Is anyone able to recommend or advise me on this? thanks. regards,mylim

Hi forum,i have a hub & spoke gre over ipsec setup. is it possible to add another router at the hub site for redundancy purpose? the router is connected to the ASA firewall, is it possible to have one connection from each router to link to two asa fi...

RT.Hi, I use Cisco VPN Client Software Release 4.7.00.0053, connect to a Router which acts as a EZVPN Server, but after each connection, it always broken after 100 to 110 seconds. the Router is C2811 with IOS 2800 Software (C2800NM-ADVIPSERVICESK9-M)...

Hi;I need to configure My pix so one of my clients can extablish a VPN tunnel the outside?outside --- PIX -- Client (VPN Client)what access lis needed to be configued on the PIX?help please.

The current design for my work design is that VPN concentrator (we have got only one) is behind PIX firewall (we have got 2 one is for failover), and IDS within DMZ zone (we have got one).Radius Server on my local network , and Cisce security Agent o...

Hi,I was wondering if it is possible to establish multiple simultaneous Cisco VPN Client connections behind a Cisco PIX 501 Firewall that is configured to use PAT. I haven't figured out how for one of our clients if it is possible.When one pc starts ...

I'm running an ASA 7.2.1 and a PIX 6.3.5. I've posted my config for the ASA, as it's what's causing me grief. I can extablish the tunnel for an IPSEC VPN on both ends (i just used the vpn wizard on both devices). My devices on the pix end (192.168...

hii have some problems with my dial backup the router makes the call but i get a message like this:Nov 7 21:18:07.051: 10.28.1.1/32 via 0.0.0.0 in 3 hopsNov 7 21:18:07.051: 172.25.4.43/32 via 0.0.0.0 in 16 hops (inaccessible)Nov 7 21:18...

Hi,I have a router 3700 running version 12.2(15)T5I have VPN CLients connecting succesfully to the router, but I have no firewall.I would like to implement an access-list on the public interface where I only acceptthe Vpn client from anywhere and den...

Hi,I can't see that the VPN 3000 series concentrators are supported in CSM. Where is the support to monitor these devices? We currently have VMS and this does contain support!!Thanks,Matt Smith

Hi pals.As you will see on the topology that i have attached, I have 2 PIX and i have already configured them for Site-to-Site VPN. I can monitor that there is an IPSec and IKE tunnel between 2 PIXes. But here is the problem, the hosts on both sides ...

Hi everyone, I am trying to set up a VPN for a client with a Cisco Pix 506E at their main office. It would be a site-to-site VPN, connecting another admin office to the main one. They have a Cisco 1721 router running IOS 12.3. When I look ...

No client is able to establish a VPN connection through the ASA unless I giive them a static translation. I know that the distant ends are allowing NAT-T connections because i see UDP 4500 when the clients are statically translated. Under normal co...

I have three ASA 5510's that are all setup identically in regards to logging. I'm using Kiwi syslog daemon to receive and monitor the logs. Two of the three ASA's logs (facility:20) are received by Kiwi, along with all three of the CSC's. One of t...