I am following this document to recover and reset the password for "cmxadmin" https://www.cisco.com/c/en/us/td/docs/wireless/mse/11-0-1/cmx-config/b_cg_cmx1101/performing_administrative_tasks.html#id_131101 When I reset my VM Server and edit ("e") in...
We want to utilise the 4 ports on the Cisco C9800-L-F-K9 to connect APs - and SVI interface on the WLC have been created on trunk TenGigabitEthernet0/1/0 with wlan 5 and 100 and - access port vlan 5 on TwoGigabitEthernet0/0/0 should these two/4 ports...
Recently swapped our 3802i APs for all C9130AXI to get the WiFi 6 capability. Have noticed very poor performance overall. Only change has been with the APs, nothing else. The controller remained to be an AIR 3504 and the switch is a Catalyst 3850 UPo...
Hi, can you help me with below. I'm having alerts on my Cisco Wireless Controller : %PLATFORM-1-NOSPACE: bootflash : no space alarm assertdevice#dir bootflash:Directory of bootflash:/381909 -rw- 53477376 Apr 23 2024 09:53:33 +08:00 .USWAP.img273 drwx...
i've seen this item "Site Tags AP to WNCd distribution" in best practice of C9800 Design and Deploymentmy quiestion is how can i configure multiple WNCd and where is the location of settings in webui?
I'm trying to get environmental stats back from 9136/9166 on Spaces. I've imported the maps successfully and have enabled the IOT service in spaces. I'm still getting errors for the TDL Telemetry under the troubleshooting section which seems to be pr...
We are operating our vehicles remotely in the underground mines over Wi-Fi, the data load from the machine is constant around 30Mbit/s (yes, six to eight HD-cameras).When switching between APs we have noticed that we sometimes get a transmission gap ...
Hey Guys, i was wondering if there is a way to allow Lobby admin to create a guest user where he would be able to specify that user is allowed to only join specific SSID. Ie: i have 2 SSIDS (webauth1 and webauth2) Lobby admin logs into the wlc and cr...
Hello all, I'm having an issue with clients connected on my Guest SSID configured with Web Authentication Splash Page. Basically by today (NO CHANGES NOR ACTIVITIES WERE DONE) all the clients which are trying to connect to this SSID cannot reach th...
Hi,Per the title, I've got an issue with 5Ghz clients that have good signal strength because they are sat almost underneath the AP (1832 APs) yet but struggling to get more than 1Mbps throughput. I can see the channel utilisation is over 50% but zer...
Hi there, I encountered a strange problem today with OWE in transition mode.Suddenly a handfull of users could not see the OPEN SSID at all. But when they moved to another section of the office they got the OPEN SSID and were able to connect. After t...
Hi Is there any document that shows that WLC 9800-40 support wifi-6 and 6G band! I cant find that document
Wired guests are not able to get out to internet, they can ping only at when payload is set to 1300 bytes or lower, this seems like an MTU issue, but its only effecting wired guest not wireless guest. Setup is a 9800 foreign on 17.9.5 code and 5520 a...
Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...
Good afternoon,A new client is splitting off from a parent company this Fall. They current have AP1852E-B-K9 and WLC5200 and they want to migrate to 9800-WL. I will have an instance of the 9800-WL stood up before cutover, but once the WAN is moved fr...
