is it possible to enter several commande in 1 line without doing the [enter] commande.maybe by entering a specific caratceters that replace the ENTER command...?ThanxB
Forum Posts
Hi allI've got a PI 3.2 a new WLC 5520, which replaced 2 old WiSMs. I managed the rogue APs through the prime over all the years and have categorized them (mostly the Friendly - External ones).So I don't have Rogue APs on the PI, but if I go directly...
Resolved! Cisco WLC 520 and LAP 521 Setup
Hi, im looking for a guide that will help me configure the WLC 520 and LAP 521 Access Point.I have searched the Internet and i found on Cisco website a statement that this model is obsolete?does that mean we cant find document about this WLC and AP?T...
There are two ssid configured in Cisco 5520 WLC.1. universal2.kicuniversalBut when client getting disconnected from ssid (universal) in every 15 min and automatically connect within 1 min. This is happening frequently in every 15 min. If users get co...
Hello. This is my 2nd problem with 5ghz wirless. Before 371 i had wap571E and i got the same problem. After 2 days of working in my home network (small apartment), wi-fi is slowing down. After 2 days i got 1000ping and speed 0,5 Mb/s. Any sugestion?...
Resolved! Change the name of an active AP Group?
Is there a way to change the name of an active AP group? I don't see a way to do it via the GUI, but is there a way over the CLI? It seems pretty counterintuitive that we'd have to create a new group, then move all APs to that group causing them to...
I am adding new APs but when they boot up they use the address of one of the Switches making it impossible to SSH into the switch.Isn't the AP suppose to make sure that the IP address is available?How can I force the AP to change its IP address witho...
Is there a way to utilize WLCCA to perform a config-diff, i.e. compare device configs from two or more WLCs and find the differences?
Hi Guys, I have 1552E AP Autonomus image and I converted into LWAPP image to be able to join WLC. But after convert the AP it's restart always and show this mesage:AP image integrity check FAILED! *Mar 1 00:00:48.263: Release image validation fail...
we were able to use all SSIDs on our Cisco Ap Aironet 3600, after maintance from Global server , we are unable to see the SSIDS to connect, 2nd thing : some time the AP blinking blue & some time Steady Green but going to Stable Blue. in the GUI inte...
Resolved! editing "DCA channel list" for 5Ghz band
on wireless controller I found that there are only few radio channels are available for usage From my understanding, that may cause a problem for clients. Is there any command available to add channels to "DCA channel list" or this list is an attribu...
Hi All,We currently have HA 2 x 5508 WLC running 8.0.133.0 and want to purchase & deploy the new 3800 APs. We were told that we need to upgrade to version 8.4 for 3800APs connectivity? Is that correct and is version 8.4 stable ?Any suggestions are m...
Here is the run down. Purchased an 1850i with CAPWAP. Converted to ME with AIR-AP1850-K9-8-5-103-0.tar. Configured ME as stated in the guide. After configuration, I cannot access the ME GUI. I can connect to SSID and access the internet fine. W...
Resolved! Compatibility between AIR-AP1242AG-N-K9 and AIR-PWRINJ4 : is the latter power injector suitable ?
Good morning all,Just a simple question:Can I use the Cisco Aeronet AIR-PWRINJ4 with an AIR-AP1242AG-N-K9 wireless device ? (I realise that these normally are powered by an AIR-PWRINJ4.)If it's not suitable, what would be the reason?Thanks in advance...
Hello Wireless Experts I have a live deployment scenario for Cisco AP ( AIR-AP1832I-D-K9 ). Considering its Cisco Mobility Express feature please add your suggestions on deployment. Its my first deployment for Mobility Express. However got to know it...
