Hello,I want to configure the Cisco AIR-AP1851I, but it keep displaying those messages: [*01/10/2019 22:53:56.6099] Resetting wired0, ifconfig down up[*01/10/2019 22:53:56.6099][01/10/2019 22:53:58.6299] IPv6: ADDRCONF(NETDEV_UP): wired0: link is not...
Hello All,I have a WLC 3504 and 5520 configured with HA SSO having 8 APs (2 RAPs and 6 MAPs). The WLC is upgraded with 8.5.140.0 firmware. The WLC(s) are in sync with SSO enabled. The AP(s) are configured in 802.11a mesh (5GHz). On commanding a force...
Hello everyone,I want to implement the RADIUS protocol over my WiFi network as part of AAA framework. The radius servers are deployed, as well as a testing SSID. The authentication on WiFi is based on EAP-TTLS-GTC framework with an LDAP database as a...
Hi, guys.I just got my feet wet in wireless mesh configuration after reading the greater part of 90 pages of the Cisco mesh deployment guide. And I succesfully made a wireless bridge using meshing with VLAN support and all.. proud of myself using ...
Hi All, We are planning to use spare wireless access points (AIR-CAP3702I-A-K9) in Israel.Could you please confirm whether this would be an issue in regards to the regulatory domain?(Regulatory domain in Israel is -I) Thank you. Kind regards
I have an RV340 connected to a SG350 and a SG300, all wired with Cat 6. The two AP581 ports are automatically LAG1, I have the two SG350 ports as LAG1. I have tried every setting possible and have yet to achieve 2.5Gbe with this access point.
Hi All, I have banged my head against the wall for the last day looking at a strange issue with my wireless controllers. My existing setup was a Foreign Controller cluster(8.0.140) and an N+1 foreign Controller (8.01.121). I then had two individual...
HiThere are two controller and core switchin core i will create vlan 94int vl94ip addd and int g1/1switchport mode trunk in the wlcInterface Name Port Vlan Id IP Address Type Ap Mgr Guest-------------------------------- ---- -------- --------------- ...
Guys, I just upload the Mobility Express image to my Cisco WAP 2802i, After complete the Wizard I can't connect the WAP, not even by Wifi or wired. Notice that I have not configured DHCP Server due to I pretend to use the WAP in a Standalone mode a...
After almost a year without a problem, this just happened!Nothing was updated, nothing was changed, it just happened.Out of 50 AP-s I lost 5 of them. I can see then without a problem they get address from DHCP server, and they have their hostname in ...
Hi, I just wanted to confirm whether it's possible to delay the JSON POST request to our custom server in Scanning API. As per as my understanding the default time that meraki cloud call JSON POST request to our server in scanning api is 1 minute. Is...
Hi,We have 5 Access points. Some of wireless users are complaining that they are experiencing poor performance at their end of the office.There's nothing obviously wrong and there's been no changes to AP location, underlying infrastructure etc.I HAVE...
I just bought a cisco 1141n to play with and when i turned it on the logging on the console said "Interface Dot11Radio0: not starting because stop-on-failure set"I am also getting insufficient power message. using a 3500yl from hp that is poe so not ...
We've got 7 MR16's deployed, with two SSID's broadcasting (company and guest)However, on a single Access point, as we get within it's range, it says the password is incorrect for the guest network. Wander 6 feet away so you're in range of the AP's an...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
