Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Team, I have a 3602I-D-K9 AP which gives me a throughput/speed about 50-60 Mbps (differing) at 5GHz , However when I configured AIR-CAP3702I-D-K9 the results are not quite pleasing ,it gives me throughput/speed about 30-50 Mbps(differing) at 5G...
Hello, I am experiencing an issue of wireless clients being dropped during the process of key exchange to mobile. This happens every 30 mins.Bellow is the capture of debug client. Dot1x_NW_MsgTask_0: Dec 12 17:36:57.435: xx:xx:xx:xx:xx:xx Starting ke...
Good morning, i have some troubles with an SSID in my Wireless environment. Some clients, apparently doesn't have internet access on that SSID, others can surf on internet correctly. Are there some debugs that i can perform to solve this issue?...
i create new AP groups and my Access Point add to this groups everthing is ok but i have 1 problem when AP connected PoE switch dotradio dont be up automaticly only I can up with console and cli why? pease help me guys MY access point model 2702-E-...
Hello Experts, Recently I have bought 2 units of MSE 3365 and upgraded them with 10.5.1-26. Initially I was able to have the console access to the extend that I configured the ethernet IP (mgmt) and CMIC. The moment I was successful to have the ...
WLC Model: Cisco 5520SW Ver: 8.2.161.0We have multiple SSIDs configured and each is mapped to a certain VLAN on the network. I'd like to block certain MAC from connecting to a particular SSID on the WLC.Using MAC filter doesn't help as it allows list...
I have 2 of these. what are simple step by step what to do? try to access web user interface to program or does it need to be accessed for initial set up via putty or cmd? please help
With Cisco DNA fast approaching Im wondering if there will be a day where cisco forces everyone to go down the meraki route and do away with a wireless controller altogether. What do you guys think?
We are unable to see the radios APs available... we connect direct to to the POE 110SG-24 ptos switch but its star blinking as it is running and suddenly blinking form red-blue-green-off .. .as we read it means it doesnt have enough power... but we...
Hi all, We want to disable to SSL v2 and SSL v3 for WLC web management . And we want to enable TLS version for web gui access. I have seen the below command to disable SSL v2 config network secureweb cipher-option sslv2 {enable | disable} But i haven...
I'm trying to write a script to automate putting APs into virtual domains. I have a database with AP mac addresses and which department they're in (which will be used to pick their virtual domain). I've successfully written a script which pulls all t...
Hello allmy AP 2602l fails to join the vWLCWLC software version = 8.5.135.0---------------------- here is the error message in AP *Dec 11 14:12:05.003: %CAPWAP-3-ERRORLOG: Certificate verification failed!*Dec 11 14:12:05.003: DTLS_CLIENT_ERROR: ../ca...
I config SSID Guest portal and try to client connect after that browser not show page login user and password.try via Chrome, Firefox, IE can't show page login but Dolphin can show page login after Except Certification.
For the best practice and performance of an AP 1562E: What do you recommend, using 2 dual band antennas or 2 single in 2.4 + 2 single in 5G?
Resolved! WebAuth Certificate on 5520 HA Cluster
Hi guys, I have a little question for changing the certificate for web authentication. My setup: - 5520 WLC HA cluster software Version 8.5.135.0 - L3 security web auth passthrough (guest access) To avoid browser error messages I changed the ce...
