Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dears, I am asking about the possibility to connect an AP to an ethernet port of a MAP to join a Mesh topology as below RAP<--Wireless backhaul-->MAP-1<---Ethernet Cable--->MAP2<---Wireless backhaul-->MAP3 I am using Mobility express installed i...
Hi, Is anyone able to assist re the exact SKU for the rear brace / bracket for the 3504 rack mount tray? The installation guide has information, but I'm having trouble translating this into a usable SKU to order. Any assistance would be appreci...
Hey all. I work in a warehouse and we have 18 APs all connected to an AIR-CT3504-K9 controller. We have one spot within our warehouse where we have some PCs that are between a modular office and the bathrooms. The ceiling is really high up (maybe ...
I know that WLC5520 has a logue ap feature, but does this only detect unauthorized devices or aps?Or is it detection and blocking at the same time? And if I block it, can I check the separate log 'I blocked when and which ap' ?
Resolved! WLC9800のentryログについて
お世話になっております。WLC9800のSyslogにて以下のようなentryログが頻繁に発生するのですが、どのような状況か分かりますか。頻度が高いときは1分おきほどで表示されます。channelの数字は変わらないので、ローミングなどではないと思っています。Nov 6 16:21:04.095 JST: %CLIENT_ORCH_LOG-6-CLIENT_ADDED_TO_RUN_STATE: Chassis 1 R0/2: wncd: Username entry (********) joi...
Resolved! AP Losing their name after staging
In the last couple of deployments our APs lost their name when reconnecting to the 9800 after initial staging. This has happened whether we changed the name in the GUI or via the console on the AP. Anyone else seen this behaviour?
Hello,I'm facing an issue with our APs dropping clients for some reason. I've examined the logs and I can see it going in a cycle of removing and adding users. We are experiencing this on a range of devices including Android phones and Windows laptop...
I've got the WLC added via SNMP without any issues, but for some reason, the AP's are not populating. The AP's are a mix of 9176, 2802, & 3802's. The VLAN has been discovered in Prime, Not sure what is missing or what might be causing the AP's to n...
Hi All, I am planning to migrate from Cisco C9120AXI-S EWC to Cisco Catalyst CW9800 controller. Is there any updated and accurate procudure to do that ? Total AP is 5. If you recently the same thing before, please share with me. Thank you.
Resolved! 9800 Dynamic Vlan
I test dynamic vlan on my WLC 9800 with cisco ISE. When the client successfull authenticate to ISE then the client will get vlan 101 to the client, but why the client not getting ip address? Vlan 101 already add to the flex profile On the client mon...
Dear all Does anyone know if it is possible to use multiple (secondary) IP Subnets for a wireless client VLAN on the C9800 IOS-XE platform?With AireOS WLCs that was not supported and we had to use either one (primary) subnet per client VLAN/dynamic i...
Hi.Trying to setup bridge/mesh between to 1815w APs, one of which is also the ME WLC. Is this possible as im having no luck. Ive tried following a few docs but not managed to get it working. When i change the MAP AP to flex+bridge mode and after a ...
I have a Cisco 9800 WLC running 17.12.5 and I have 1 central site (local mode APs where the WLC resides) and about 10 remote sites with APs in FlexConnect Mode and Local Authentication. Each remote site has a local authentication server with the auth...
I have a branch office where the APs get their DHCP from a Catalyst 9200 that includes the option 42 NTP server. I recently needed to update this, and realized that, since those DHCP leases were setup "infinite", I don't have an easy way to getting t...
Resolved! 1541i APs failing, PoE only no ethernet
HiWe have been getting failures of 1542i AP for a while but though it was an environment issue but we are getting more and more failing now and some are not in a bad environment. When they fail the switch shows the port down, PoE shows as ieee PD. ...
