Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, I am preparing a Cisco Wi-Fi proposal based on Wi-Fi RFP requirement. Please if someone can share the following Wi-Fi Pre - Sales support material which will assist us in proposing Cisco Wi-Fi offering. Cisco Boilerplates of AP , Controller, NMS,...
Guys, Does anyone know how to disable these Power type/POE trap logs on the wireless controller? I can't see a related checkbox in the SNMP trap controls section. I have disabled Auto RF Update traps - TX power update, pretty sure thats related to ...
Hi All, as with my previous is am starting this thread as a help in configuring the Mobile Concierge Service.As the solution is new the documentation is a little light in detail so this is obviously a good place to document in more detail the set...
ok, got a really weird problem that we are stumped on. We have a remote site of 3 buildings, building 1 and 2 have wired AP's and building 3 is a mesh due to lack of wiring. Now, they work fine on the wired AP's but act like the PSK is incorrect on t...
When using Cisco Mobility Express, is there a way to block a Mac address from authenticating?
Hi guys, I recently had a site survey completed at my site. After taking a look at the survey results, I noticed that there was tons of channel interference on the 5 GHz radio every where. Interfer Severity almost 100%. So I took a look at Cisco P...
Hi there,I currently have two 3650 switches (IP Base; with AP licences; not stacked), ten 3800 802.11ac Wave 2 Access Points with Mobility Express Licenses and one WLC 5508 with 12 APs licensed. The 3650 are MGIG capable.I would like to be able to sw...
Hello Experts, I downloaded the Cisco sample custom page on Cisco WLC, but still I see that internal logout page is coming up. Login Page and Login Failure page is working but Logout page is showing from internal webauth!!!! Means Internal Logout is ...
Hello all, In a Cisco WLC 5508 with firmware 7.4.110.0 a Windows 8.1 PC cannot access the GUI, tested with IE, Firefox, Chrome. The same PC was till now able to access, while the Windows 7 PC have no problem. Any thoughts?
I have a cisco WAP4410N Wireless-N Access Point. I am trying to set up it but the IP 192.168.1.245 is not working. Anybody can help me, explaining how to fix this issue?
We purchased 3702e AP's with AIR-ANT2524DW-R antennas, and will be mounting some on the ceiling and some on walls. How should we position the antennas that are mounted on the ceiling and how should we position the ones that are mounted on the walls....
Hi All, is netflow supported on virtual wlc version 8.2.121.0? if so can someone point me to a config guide? I found one that states I should go to WIRELESS -> NETFLOW. I do not have a netflow entry under WIRELESS. Kind regards, Vincent Dumont
We are having an issue with the Cisco WAP561. We configured it and it is working via POE however after a few hours maybe up to a day it will than stop allowing some clients to connect that were able to earlier in the day and will reject anyone new t...
I am deploying new 2700 series AP's to a 5508 but I want them to disable their radios when they first connect. Reason being is these new AP's are being installed in a live environment with old 1200 series AP's connecting to WiSM blades and I don't wa...
Hi all We've purchase two 1850i AP recently, due to it support Cisco Mobility express function, we translate one and plan let remain 18 join it, but it doesn't work properly. On the CME Master 1850i web, we can see the subordinate 18 info under "ACCE...
