Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi I have a question about CMX on Premise with a virtual MSE I have the CMX advanced license under L-MSE-PAK-N the software will be installed on a customer supplied server so I only need the CMX advanced license and with this I can get the ova for th...
Hi there, I try to add the meraki to our prime as I see in the meraki docs. so far so good. But I get always the error "SNMP Failure: No Response for SNMP Get request". I added the snmp.meraki.com and the meraki customer URL nxx.meraki.com with the S...
Hi all. I have a site that is misbehaving and I would like to run my findings past the knowledgeable people of this forum. Here is the scenario: Two 4400 WLCs in mobility group TEST ~ 100 APs all running in local mode One WLAN Profile 15 different lo...
Very vague issue I know. From what I have gathered so far, download speeds on the wifi are fine at times and sporadically slow at 4Mbps downloads on a 100Mbps circuit. I do see some drops on the Internet circuit connecting interface, but not a very h...
Hello Community, I was fooling around with CAC(Certificate Based Login) on my admin console and now I can't log in. How can I disable this from the CLI or is there a way to change the node from admin to standalone from the CLI? Below is the error I'...
I have just recently purchased this device on ebay as a used product from a bankrupt company, which was selling off old equipments. I am trying to attempt to console into the ap, but am not able to do so, sucessfully. I am using a usb type console to...
Hi, We have a pair og 8540s running HA/SSO. Currently controlling about 500 1832i/2702i in a large number of disperse buildings. The config is the same for all buildings, same SSIDs (about 6 now, hopefully this can be reduced to 3 in 2017). The quest...
Hello, I recently add a new AP 2600 series in my network. I have WLC 8.3.102.0 and Prime 2.2.0.0.158 but I can't view that access point on it. That AP works well with users connected. Any idea! Cheers
my 1242ag lwapp try to join my 4404 controller, but during process "lwapp changed state to discovery" and nothing happens. i found out that time on lwapp is wrong, but changing the time is not working because "nvram verification fail" tried "write er...
Hi Guys I have a number of 5508 controllers running software version 8.0.133.0, I am now experiencing a number of issues, these are listed below, I wonder if anyone else has had the same 1. Wireless to Wireless voice issues 2. Voice Break Up (Whilst...
I recently bought the WAP 371, but experienced frequent disconnects on both 2.4 and 5 GHz channels. After upgrading the firmware to 1.3.0.3 the disconnects are gone but the throughput is very low when browsing the internet. Downloading seems fast how...
Hi, I have upgraded my WLC to v8.0.133.0 from 7.4.140.0 and I now cannot get Flexconnect clients to work. The authentication is passed across to an ISE server (1.2) and I can see that the client is successfully authenticated. DHCP server is central ...
Now I have a 1832 wireless AP, the current wireless network’s working is normal, but can not access the web interface, I would like to reset the factory settings from the external.who can tell me how to do ?
Dear Team, We have Cisco 5508 Controller and Cisco CAP-1252 with Following software version: Cisco Controller 5508 Software Version: 7.4.121.0 Cisco 1252 Software Version: c1250-k9w8-tar.152-2.JB3 As per Compatibility matrix, Software version presen...
Hi, I am currently using 1252A / G for testing. When I log into the AP, it allows me to select specific MSC type, Channel, Bandwidth, output power in the web gui. I am looking to upgrade to 3802e with wave2 capability. There seems to be a new GUI c...
