Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello Community, I'm trying to configure Cisco AIR-SAP3502I in WGB Universal mode.I have successfully made this work for none-Cisco Wireless network area... So my laptop is currently receiving the proper IP address from the main none-Cisco AP (Router...
Howdy Folks, After few days messing around i finally got my 3850 WLC to Pair with few AIR-CAP-3602I and all works perfectly with 1 exception. Every time the controller is reloaded and it boots up, all APs have their radios in Operational Status Dow...
Kullanmakta olduğumuz Cisco 2500 Series Controller (ver:7.5.102.0) ve buna bağlı olarak çalışan AIR-CAP1602I-E-K9(ver:7.5.102.0) AP mevcuttur. Bu sisteme ilave olarak AIR-CAP1702I-E-K9 (ver:8.2.100) eklemek istedik. fakat versiyonu yüksek olmadığı i...
Hi I have four Exalt R5005 microwaves. I am having troubles figuring out how I calculate EIRP. I am also having troubles figuring out the proper setup so I stay within FCC regulations. I have zero experience with microwave networking and this is a...
Hello,Im working on getting a cisco aironet 1830 controller/acces point ready to drop in on our network. In the past ive used standalone 1600's where I was able to configure mac filtering and apply those filters to particular vlans. I dont see this o...
Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and any ask questions about how to secure a wireless network with Cisco expert Roman Manchur Wireless networks have became pervasive in today's world...
I have 10 brand new 3802i AP's, they are connected to a 2504 controller. The controller is running 8.2.110.0 code. The AP's register fine but ther are two points that have be concerned. First the CAPWAP preferred mode (which i have set to IP V4 gl...
Hello, We have a few FLex Connect Groups setup (not by me) and I have just created one for the first time on our 5508 WLC. I used the GUI and all the settings look the same as the other Flex Connect groups about from what is under the tab called "WLA...
Hi buddies, Is it possible to set a secondary IP address over management port of WLC, because I need to register our WLC in an AAA server with an IP address except of available IP address. By the way our WLC is 5508 and our management port is an inte...
Hi, We have a Ubiquiti UAP-AC-PRO that we're testing, the performance of this is significantly better than a Cisco 3700 we have connected to a 5508 controller. On a file transfer we see the Ubiquiti perform twice as fast on two different 5Ghz clients...
Hi, We got a request from client that users want to use Airplay service on wireless. Please help me how to configure WLC 5508 as bonjour gateway and it is implementation. Regards, Veera Reddy
Hello, Can one MSE be managed by two different Prime Infrastructure servers, say if the Prime servers are in an HA setup or independent of each other?
I've recently upgraded from 8.1.130.0 to 8.2.110.0 (a few days ago). Spontaneously at lunch time today, the active controller rebooted. The switchover reason is "active controller failed", but I can't find anything else to give me an indication as to...
Hello Team, Need help to configure Wireless Network. i have 2702E autonomous - (8unit) with SG300-28port (1 Unit). Requirement :- 1. Multiple SSID with different VLAN on AP. 2. WDS or Repeater mode for WL. Thanks Nipul
Hi Fellows, I'm searching for a solution to disable the Ethernet broadcast setting on the WLC globally and enable it only on a per access point / Vlan basis. Is there any way to achieve this? Maybe through FlexConnect? I was not able to find any rela...
