Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi Guys, The " N+1 High Availability Deployment Guide" is pretty straightforward but it is not clear if the only one command necessary on the Secondary Controller is "config redundancy unit secondary". In AP SSO High Availability , the Backup Cont...
Hi All, I was trying to configure webauth passthru with 5760 running 03.06.00E.Below is my configuration ,I tried both with and without preauth ACL.The client is in webauth pending state . The traffic is blocked and the DNS resolution is working, ho...
I have recently installed Cisco MSE and attached it to my Prime infrastructure 2.0 appliance but the MSE backup failed with the following error MSE Backup failed for mse.xxxx.xxx.xxx.xxx. Reason: null I can't see any reference to backup errors, has a...
Hello All Can anyone shed light on how I can connect ANT-4G-OMNI-OUT-N to 4G-CAB-LMR240-25 ? I am sure that all I need is an adapter but am not sure which one ..... Please help ThanksFraser
Hi folks, I have a pair of wlc 5508, configured as a HA pair. I want to upgrade the FUS to ver 1.9. Is it necessary to break the HA pair, and upgrade each wlc individually?
The running config is:- Two WLC5508's in HA SSO setup running version 7.5.102.0- about 130 x 2602i APs I need to upgrade to 7.6.130.0 using the pre-download feature to minimize the network downtime.Is it possible to transfer the 7.6 to the controller...
Hi all,I've been getting "%MAC_MOVE-SP-4-NOTIF: Host xx.xx.xx.xx.xx in vlan 123 is flapping between port Gi1/18 and port Po1" entries on my core switches. The topology looks like this:Interface Po1 connects my two 6500 core switches, we have HSRP run...
Hi, I have a query regarding Access Point compatibility, i have been advised to buy the CISCO AIR SAP 26021-EK9 and i am wondering if this will work injunction with my current hardware: CISCO AIR AP114N-EK9CISCO AIR AP113AG-EK9 Kings Regards,Paul
Hi,I just found out that configure terminal is available on a LAP1262N AP-AIR-E-K9 in mode CAP.But another LAP1262N-AIR-E-K9 not the configure terminalFind enclosed AP version and option configurehow have the configure terminal in AP mode CAP, while ...
HiI'll be upgrading a HA pair of 5508's from 7.4.110.0 to 7.6.130.0. The documentation suggests that I just need to upgrade the active and this code is copied to the standby. Then simply reboot. After this verify that the active is not the standby HA...
Can a CISCO Aironet 700w be set up as Antonius Access Point ? I was able to set up 700i OK no problemNeed to Set it up for WIFI site Survey Active to test coverage
Hi,I'm facing an issue in Cisco 5508 WLC.My WLC IOS image version is 7.5.102.0.Problem statement: My WLC is currently in production and catering to a live system. It has to be migrated from existing data center to another. The IP address, subnet mask...
Hi,In the case, when Light weight AP is broadcasting more than one SSID ( with WLC is configured with associated VLAN interface) how does the WLC differentiates DHCP requests those are coming from different SSID before forwarding to DHCP server?Doe...
Hi, I need to backup my current config on my WLC 4400. I want to use TFTP to do so. However the TFTP server for MAC requires that I enter the name of the configuration file in my TFTP server BEFORE I actually download and save the config. But I do...
Good evening,We presently have some minimum data rates setup for our 802.11 deployment (.11b/g disabled below 9Mbps, required at 11Mbps and supported at 12Mbps+ and for .11a/n/ac below 12Mbps disabled, 12Mbps required 12+Mbps supported). Currently ...
