Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

Resolved! LAG on WLC5508

Hello guysi have a wlc 5508 , and i want to enable LAG, but i want to connect 4 ports in one module and the rest 4 ports in another module, for example Gigabitethernet1/45 - 1/48Gigabitethernet3/10 - 3/13 both modules in the same core switch (6506) o...

Enabling 5Ghz

I just enabled 5Ghz 802.11a/n on my Cisco 5508 controller.I see my client machine associted with 802.11a/n (it is my understanding that "a" is required for 5Ghz).Is there a way I can confirm I am in the 5Ghz range? (we have 2.4Ghz enabled as well)

%DHCP-3-ADDR_NOTIN_POOL: in 7.0.220

I have seen the other posts about this Syslog entry but we are running 7.0.220 and thought it was supposed to be fixed in this version.  Any thoughts?  The scope isn't out of addresses.%DHCP-3-ADDR_NOTIN_POOL: pools.c:158 Error: Ip Address 0.0.0.0 is...

jjheck by Enthusiast
  • 921 Views
  • 2 replies
  • 0 Helpful votes

Resolved! AP Number and Positioning

Hi folks,Looking at putting wireless into a large open plan building (appxox. 80M x 40M) with two floors. We'll have up to 450 clients (combination of desktop and mobile devices) spread over both floors so need about 24 APs. With 12 evenly distribute...

shanemoss by Beginner
  • 317 Views
  • 1 replies
  • 0 Helpful votes

Resolved! VLAN Over Remote Bridges (1240AG)

Hi,I've an AP connecting to the backbone switch via 2 wireless bridge links as shown below. Currently, it is operating as flat lan.Would like to know if it can be coverted to vlan mode so that I can support wireless clients of different vlans at the ...

EW by Beginner
  • 521 Views
  • 3 replies
  • 0 Helpful votes

QoS Configuration for NME-AIR-WLC

Hello,I have a question on the correct QoS configuration for a VoIP deployment. I have followed the steps referenced here but have two questions..1) The last recommendation in the list is to set DCA channel sensitivity to High to avoid changes during...

Wireless LAN design

Dear All, Can you give opinion how secure is it connect WLC based Wireless LAN to existing LAN and wireless traffic will go through firewall in order to reach server farm, however, it will only go through ACL for Wireless to Wired LAN access. Please ...

adilhayat by Beginner
  • 623 Views
  • 1 replies
  • 0 Helpful votes

a/g/n and a/n

why in cisco WLC we find a/g/n and a/n ? I mean why a/g/n togather and a/n togather ? what is the relationship in a/g/n and the relationship in a/n?? byanother words why a/n companed togather in WLC orWCS and the a/g/n also comained togather also why...

Wism software version

Hi,I have  a new  Wism to install and it has version 6.0.196.0 I saw that there is a software advisory to stay way from this version. I was thinking in install/upgrade to version 6.0.202.0 but reading release notes i see the following open caveat  Wi...

etmarcof by Participant
  • 287 Views
  • 1 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Unanswered Topics