Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi EveryoneI'm seeing the following message in my logs every 30 seconds:396901: Apr 2 2014 13:31:20.958 BST: *capwapPingSocketTask: 1 wcm: %CAPWAPPING-3-PKT_RECV_ERROR: capwapPingSocketTask: capwappingRecvPkt returned errorDoes anyone know what thi...
Hello I hope get some guidenance on how we can resolve this issue. We have certain 2nd floor rooms that are having issues with Wifi connection named Student. The students can connect to it on there chromebooks but connection is slow and lagging. Mean...
Hello.In policy enforcement by device type, IPHONE is set to BLOCK for SSID.However, your iPhone is not blocked.Do you have a case like ours??What is the solution??I've contacted Meraki support, but it doesn't help.Please help me
Hello team ,we have a setup of C1852 as WLC and joined CAPWAP AP 9130usually the default mode for 9130 is dual mode with means slot 0 for 2.4 and slot 1 for 5 GHZi found that it operates in Tri mode which means it has slot 0 for 2.4 and slot 1 and sl...
Resolved! Cisco 9800-CL HA setup issue
Trying to setup redundancy on 9800-Cl in Esxi environment. Have three NICs - Gi1 ( OOB ) , Gi2 ( trunk ) , Gi3 ( HA ) . After issuing following commands and reloading controllers one of the controller goes into recovery mode and HA is not formed. Co...
Hi All Can anyone tell me the benefits of increasing TX power on an access point? does it allow the signal to go further? or faster etc ?
Resolved! 9120AX login fails after reset
Hi all and thanks in advance for any advice.I have had the same issue now with two 9120AX APs where following a hard reset, pressing the reset button for longer than 20 seconds, I'm unable to login to the device either by SSH or console. Neither the...
[*09/04/2024 18:35:52.0000][*09/04/2024 18:35:52.0001][*09/04/2024 18:35:52.0001] CAPWAP State: DTLS Setup[*09/04/2024 18:35:52.3783][*09/04/2024 18:35:52.3783] CAPWAP State: Join[*09/04/2024 18:35:52.3797] Sending Join request to 10.48.40.45 through...
I was wondering if there was a way to see the last known connection for an access point. When an access point is connected, The dashboard will show you where the access point is connected (Switch name, IP address and port number on the switch). After...
Hello, I've tried with MR36 and MR76. If I go to the Status Page and switch the AP in survey mode, the 2.4Ghz starts ==> it's OK !I also want 5Ghz for my survey : I've read that first, I must claim the MR in the dashboard and connect the AP to the cl...
Resolved! DHCP Relay Over WAN
I have 3 flexed WLANs at a branch that will receive DHCP from Windows at our DC. I'm unsure of what to set the relay to. Is it our L3 SVI which in turn relays to the DC or do we set the relay to the IP of the Windows server at the DC? Thanks in advan...
Hi there,we are seeing huge interference on channels 1-3 on the RF Spectrum page from two APs in the same area. We have no equipment running on these channels and the floors below and above us are also controlled by us and do not use channels 1-3. Ha...
Hello,I use external captive portal with RADIUS server on my 9800 WLC. I was using 17.6.5 and upgraded to 17.12.3. After upgraded it, on the RADIUS start packet username looks as clients MAC address, it was userxxx before. Is there any configuration ...
Resolved! What is Aironet IE? I have my clients disconnected from when uncheck the Aironet IE in WLC 5520
What is Aironet IE? I have my clients disconnected from when uncheck the Aironet IE in WLC 5520
my AP (AIR-CAP3702E-B-K9) seem to loss its firmware. attached is the startup log when trying to reset it using the mode button. any help would be much appreciatedIOS Bootloader - Starting system.flash is writableTide XL MB - 40MB of flashXmodem file ...
