Hello Team, I would like to know if I am allowed to convert a CAPWAP aka. Lightweight Access-Point to EWC? Would it be possible to convert a C9120AXI to C9120AXI-EWC after owning the AP, or is it against the licensing from Cisco? Thanks for your ...
Forum Posts
Hi,I checked data sheets of Cisco Catalyst 9800 Wireless Controller (Cisco Catalyst 9800 Series Wireless LAN Controllers - Cisco) and Cisco Catalyst 9100 Access Points (Cisco Catalyst 9100 Wireless Access Points - Cisco - Cisco).Cisco Catalyst 9800 W...
I have an 1850 access point . It is working fine as an access point and I can SSH into it no problem, however, I cannot access the web interface using any browsethis problem started before two days agobefore that I accessed the web interface using a...
Hello, I cannot access the Mobility express administration panel, i get the error ERR_EMPTY_RESPONSE.through ssh I can login, what can I do to restore the administration panel? Thank you in advance
I have an 1850 access point running Mobility Express. It is working fine as an access point and I can SSH into it no problem, however, I cannot access the web interface using any browser. Tried Safari or Chrome. When I connect using Chrome using ht...
Hello,i am kind a noob in cisco networkingso i have a small network with an 9800l wlc, 32x c9105axi-e,7x c9124axi-a and 3x c9115axi, a few cbs350 and a few c9200. There is a vlan hosting 30 apple tvs and same vlan is on WLAN SSID no3.Every client con...
Hi board,in AireOS, P2P blocking is supported only if the wireless clients are on the same WLC and in the same VLANAre there the same restrictions for the 9800? Assume client1 and client2 are in the same SSID but are assigned to different VLANs. Is P...
HI , I know IOS AP can be format flash by "fsck flash:". For ClickOS AP, I don't know how to format flash. If you know, could you tell me?In addtion,I also want to understand the following questions:1. How does the AP enter (RNAQ-C7) # mode?2. How do...
Hello, I facing an issue upgrading an AP4800. I don't like the version is too old to connect with the Controller or something more rudimentary. The controller is a 3800 ME 10.151. The Ap4800 is running 8.7.x. I can get even to ping. Tried multiple wa...
Resolved! C9120AXI U-boot issue
Hello,One of my home APs stopped working after being reset via the buttonHere is the log:U-Boot 2017.09 (May 21 2020 - 19:22:05 -0700) Broadcom BCM49408 Board: VANC-iI2C: readyDRAM: 2 GiBenable MMU ... OKNAND: Status wait timeout: nandsts=0x0 mas...
Resolved! C9800 ports and IP addressing
Hi,I have two physical C9800. I want to check my understanding about ports IP addressing:two service ports share the same subnettwo wireless mgmt and RMI share the same subnettwo RP share the same subnet Would this be correct?In addition, should the ...
Dear all:I'm attempting to solve this issue, but I'm having trouble.The customer has this error, which is the problem.Page in blank and the error ssl_IDMISMATCH
As shown below, what may cause the following channel changes？ can't understand the meaning of "Signal Strength"low SNR? or othersChannel changes will cause users to briefly disconnect from the network, I want to reduce the impact
Hi, I can't get http/https/ssh sessions to standby WLC 3504 when primary is off, version 8.10.185, all clients communications work well... The WLC respond to pings Is it normal or is there any configuration to solve this? Thank you Cheers
I have a simple setup of WLC 2504 v8.3.150.0 + 1142 + 2702 + RVS 4000 router with no VLAN. My requirement is to setup these two APs in FlexConnect mode. I have provided the snapshots of settings for the SSID. I have created a separate AP group for th...
