Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
We just upgraded light-weight APs (AIR-CAP3502I-A-K9) to 7.2.110.0, and now we get APs which disapear off the network: They are still getting POETheir light is blueThey do not show up on CDP neighbor command, even though the port is still showing con...
I have 2 WiSM with 6.0.199 code and i have a question its supported have a hreap aps with a NAC in-band acces?Regards!
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC. Any advice?
Hello.Here we need to set up Network Access with OOB wireless and authentication via Active Directory. I have followed this guide but still can't get it work.http://www.cisco.com/en/US/products/ps6128/products_configuration_example09186a0080a138cc.sh...
I have a 4404 controller running 6.0.202 code and more more people have Mac running bonjour and wanting to use Airplay. I see how to turn on Multicasting and even provide a Multicast address for IGMP snooping but does anyone have a good feel as to t...
Can I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a ...
We have a customer that is looking to allow only static IP addresses onto the wireless network via the new 5508 we are putting into place. Any ideas on this? I can see where to require DHCP but not the opposite.
Hello All,We started seeing a lot of complaints coming from clients campus wide stating that they are not able to connect to our secure wirless lan. The behavior is the device will try to connect several times then come back with a can not connect e...
I am using Cisco AP " WAIR-AP1252AG-A-K9". Please inform me how to Set the Below modes to this AP using (a) GUI (b) CLI commands(1)802.11b Only(2)802.11g(3)802.11b/g(4)802.11b/g/nThank YouPramod Ganigi
Hello all. I have an issue with some clients that seem to have poor ping times but I can't give the users a reason why. Pinging from all tested wireless clients to their respective LAN gateway router almost always results in 3ms to 10ms response tim...
Need help with Security Monitor > Intrusion Alarm...I have specified the "Recipient To:" address for email notification and selected "New client detected" and "New Access Point Detected" for reporting by email notification but never receive any such ...
Helloim new in wireless and have delegated a task to setup a wireless connection between two buildings (it should be on the same IP subnet), app. 300m apart. I would appreciated if someone give me some ideas how to perform this task, what Cisco AP to...
so...we bought a bunch of cisco 3600 series aps with external antennaswent to http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps11983/data_sheet_c78-686782.htmlfollowed the link 802.11n antennasand choosed the right antenna for our purpose...
Hello,The NCS (1.1.1.24) tells me that there are 13 critical errors with the controllers. When i click on it i see nothing. When i look at critical errors from ap's i see the critical error. Anybody else this problem?
Greetings!For 3 years now, I've been using an NME-AIR-WLC25 controller with an ever-increasing number of AP's (reaching the 25 limit a few months ago). As part of a new construction project, I'm adding 5 more AP's onto my network. As a result, I purc...
