Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Wireless N Speeds?
Hi I have a 1252 access point and have a questions about the connection speed.I am running off POE which as i understand only has enough power for 1 of the antenna modules.I have disabled the 5GHz module and am running only the 2.4GHz module.When I c...
How do I configure a WAP4400N as a bridge to a WRT310N? When I set the WAP4400N as a bridge and use the MAC of the WRT310N I am not able to communicate between the two subnets. What is missing? Or are those two devices not able to communicate in a br...
Resolved! AP cannot register on WLC 5508
HiAP cannot register on WLC 5508. WLC connects to 4507 as trunk port. Layer 2 vlan / Layer 3 vlan and DHCP Scope are configured on 4507. On WLC the interface got IP address and DHCP IP address. Access Points connects to POE Switch. There is a trunk...
We currently have a Spectrum Expert PCMCIA card that works very well and we cannot afford to move over to the USB style analyzers at this time.My question would be if anyone has sucessfully used a PCMCIA based card with a computer that does not have ...
Resolved! Upstream bandwidth QoS profile 5508 WLC
Hello,Is it possible, through a QoS profile, to control how much bandwidth a user gets to use for upstream traffic? I can easily set limits for downstream traffic, via the per user bandwidth contracts, but it is not obvious to me on how to control u...
Hi,We are using 5508 WLAN controllers in our corporate environment. Few users started getting Limited Access Connectivity. Eventhough we enable and disable wifi adapter it was the same case..The signal strength of the Radio is Excellend and when i se...
Resolved! Cisco 881w AP Gui problem
Hi,I'm trying to configure the Cisco 881w Wireless Router i bought, but when I try to access the internal AP using the web page, the web page is broken and i cannot sign in to it. I searched the forums and the only thing I can find is that this bug w...
When I configuring APs with H-REAP with multiple VLANs. Do I have to trunk the APs LAN interface and Switchport?
Resolved! Cannot drag and drop AP in WCS
New to WCS, I tried uploading floor area in a building which was all fine, but when i select an AP from WCS and try to drag and drop to the right place it wont move.Any suggestions are appreciated.
I just would like to know how to design for the location tracking solution such as 1. How to calculate AP deployment per sqr m. for accurary tracking ?2. For the location tracking solution, What we are should be consideration ?Thanks for your answer
Hi,I have a requirement to land an SSID on an anchor controller but depending on which AP the client connects I need them to receive certain IP address.So...I have an LWAP known as AP1 connecting to WLC1, WLC1 uses WLC2 as the Anchor controller for t...
Hi I may have few question about service port interface on wlc 5508. Is it possible to do the port as public zone for remote? Because i have problem with remote wlc via internet (wlc is the private IP-address and it have not Nat also), so, anyone or ...
Dear All, i configured a dynamic Interface with Primary and Secondary DHCP Server. For testing purposes,we simulate that the primary DHCP is dead. Does anyone know what is defined as "Dead Criteria" for the primary DHCP? When will the WLC start to us...
Hi,Regarding the subject, anyone can enlighten me which one is better for setting the channel assignment of Lightweight on WLC?Does it better to use "Auto" or manually setting the channel/power on each individual AP.Thanks,
How long is a complete CISCO study, till im proffesional!---Posted by WebUser Alroy Ndhlovu
