Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello communityI need your help, the company’s APs are no longer transmitting internet traffic to certain computers or 20% of staff are affected by this issue, and here is the message when they try to connect:"THIS NETWORK HAS BEEN DISABLEDplease con...
Dear Everyone ,We are having issue to join the cisco 2702i AP to our new 9800 WLC . After collecting the debug IP and debug mac address from the 9800 , we found out the 9800 was the one drop the dtls connection with below reason : 2024/06/24 12:38:28...
Hi Community.My problem is currently the PC shows no internet and no internal communication even though the wireless client shows as connected in the dashboard.It can be said that the usage environment consists only of Meraki products.Wireless users ...
Hi Team,we are planning to install C9130AXE-STA-B (C9130AXE wap with C9104 Antenna) bundle. can you pls help to guide type of mounting bracket will be used for wall mounting. i referred below link also but it does not confirm what is the part number...
Resolved! WLC controller AIR CT5500 AP
Hello team, recently our client send us a question about software for end of all device. We suggested new device, but it is working properly, so they refuse. Does anyone have this: AIR-CT5500-AP_BUNDLE-K9-8-5-182-0.aes Thanks, br.
Hi all, We are experiencing a strange problem with our WLC 9800 running version 17.9.5. All iPhone devices can't obtain an IP address and get stuck on IP learn mode with the 5 GHz band. If we disable the 5 GHz band, the devices work fine with the 2.4...
Resolved! Upgrade Catalyst 9800
Could someone please help me out with this? Cisco wrote this so confusing I need some validation. I am planning on upgrading my Catalyst 9800-L to the recommended code version 17.9.4a. When I look at the APSP release notes it states that I need to in...
Our school district has a large Wi-Fi network with over 4200 Catalyst 9K access points (APs) spread across multiple campuses. These APs connect back to a central data center with two Cisco Catalyst 9800 80 WLCs and two 9800 40 anchors.We've been batt...
We have a open SSID w/Radius setup on our MR46 APsWe are using Radius w/Group Policies to drop these devices into the appropriate Vlan on our networkAll of the devices are set to Auto-join this SSID.We're are using Apple iPads and Chromebooks which n...
Hello all, My current environment consists of a WLC 5520 with mostly if not all 9120AXI ap's on prem. Our current setup for guest wifi does not use ISE authentication it simply allows the end user on the network via captive portal.VIP is requesting t...
I am attempting to obtain a copy of the WLC config from the controller via FTP from GUI and SSH. Multiple FTP/TFTP servers have been attempted, but we keep getting the following error. cisco updcode.c:6888 Error FTP file Transfer [ftp_put], <150>, Op...
Resolved! Cisco WLC 5520 GUI and CLI stuck
Hello,We have an EMEA central WLC, Cisco 5520 in HA with firmware 8.5.171.0, hosting around 400+ APs among multiple countries and sites, I was working on the CLI for reviewing some APs logs earlier, at a moment it got stuck.Since this moment I cannot...
All access points (APs) under my C9800-80 controller are operating in local mode. I have two different SSIDs: one with WPA2 Enterprise and the other with open (central web authentication with ISE). There doesn’t appear to be a general issue, everyth...
Hoping to get some help here... we are baffled.There are 400+ commercial IoT devices (all the same) on the wireless network across several campuses. These devices have always connected very quickly and have been very stable.Internet shortages, chip ...
1. trying to block DNS IP (which is outside AdP domain) from a device in IOT .. IOT has tag 268, for DNS I create an adaptive policy object with DNS IP, then tied policy object to an SGT (10) in a group, then created a policy to block traffic between...
