Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello,Our current wireless infrastructure is getting somewhat dated. We have 2 4404 WLC's and all of our AP's are 1131AG's. We have been investigating upgrading to 802.11n and have been courted by some non-Cisco vendors promising better performance...
Currently I have 700-1000 clients connecting to my WLAN using a single SSIDand all are dropped into the same vlan by my controllers which have a 4G etherchannel into my core.No one's complaining about service quality yet, but on the wired side I norm...
I am receiving tons of this messages:%DOT1X-4-INVALID_MSG_TYPE: authlib.c:86 Invalid message type 9 received from AAAi did debug my radius server (freeradius) and show nothing about "message type 9"Someone with the same issue?We have 60 Cisco LWAP ap...
Hi,While connecting users to wireless connection getting Limited error connectivity message by using AP1142N with H-Reap solution. The user is able to connect without any problem with other buidling AP with same solution.Please let me know....what co...
Hello,I have MSE 3310 ,which is connected toWCS.The problem that I can not see the exact location for the devices on the heatmap.they told me that they have already registered the Context- aware.can you help me please with this.What do I need to see ...
Ok, it has been a long time since I have done this and I am trying to move from an ACS setup to a Microsoft IAS setup for EAP-FAST user authentication and I cannot remember where I had gotten the information on the IAS side setup.Any help would be aw...
Hi,I have integrated WLC 5508 version 7.0 with Cisco ACS. I have enabled TACACS authentication. So, user can login through TACACS user credentials. The default admin user details are used as local authentication. My requirement is the users should l...
Hi,My customer want's to connect some printers to the WLAN. I'm trying to use a 1242 autonomous AP in Workgroup Bridge mode (Ver. 12.4(3g)JA1). The controller is running 4.1.171. The printers have a Parallel to ethernet(RJ45) converter on them.Troubl...
What is the best way to debug DHCP activity across this unit. We have this unit setup as a demo at a client site, and it is having some difficulty with DHCP...Are there optons for both CLI and the GUI?Thanks!
I am running WCS with 2 WiSM and 4 4404 WLC.I just turn on CDP on all switches and router for switchport trace features on WCS.When I tried to turn on CDP on access points I get message to turn on Global CDP features. Problem seem to occur when I t...
hi there, can u help me to figure out y ring topology & hub topology are not supported in PDH?also no intercommunication btwn systems r alo not supported may i know y?
Hi,I am running 5508 controller with version 7.0 and 1141 access points.. I am facing a problem on user connectivity.Wireless Users are getting frequent connection and disconnection. These users are not getting connected to the access point nearby al...
HiI have a WLC5508 and are using the management interface as a AP mgmt interface. I want the WLC to be the dhcp relay for the AP .The AP is on the same Layer2 vlan as the WLC mgmt interfaceThe DHCP server is on another vlan, and i am pointing to the ...
Hi friends I'm having some issues with the auth in a 7925G phone. I configured the Authentication to work with EAP-FAST and an username in the AD domain, because I'm using 802.1X. I keep getting the "Authentication Failure" banner in the phone but I ...
hello Guys, i have an AP connected to a gigabit interface on my switch. all seems well configured.a show cdp neighbors command on the neighboring switch shows my AP as a neighbor with its IP address settings.A ping to the AP is not successful. trunk...
