Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi all,i have two wireless networks with two subnet (see the attached drawing) , all controllers run v4.2 access points type is 1020 .the first network in hall 1 have 4 wlc in subnet 172.16.40.X , the security is WEP key for wireless phonethe second...
In the configurarion of PEAP the Certificate Services (ISS), the CA Type... Can be Standalone?http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00807917aa.shtml#t6Step3.: On the CA Type page, choose Enterprise root CA and...
HelloThis may be a daft question but I have no real experience on Cisco WLC's and I've been dropped in it at work so bare with me.I am wanting to set up a new WLAN on the controller and give it a private address range 10.x.x.x. Id like to NAT this o...
Hi all,I am trying to set up radius authentication for the management users of WCS. I am using freeradius.I created a user and set included the necessary group tasks in the reply using Cisco-AVPair. I can see in the debug on the radius server that th...
hiwhen i try to set SSID in my access piont with CLI. with commandAP(config)#interface dot11Radio 0 it is a invalid command.??? i tried several times. what's wrong here????/
Simple question - does removing the checkmark next to the "Admin Status" field disable the "A" radio completely? I'm trying to prevent power alarms b/c we don't have sufficient POE to power up both A and B/G radios.TIA,Amir
I have a AP1220A I'm looking to configure it so that it blindly connects to any unsecure network.And then I will be able to use the CAT5 to provide my router with internet connectivity.Is this possible?
Hello everyone, I've been trying to track down a very stubborn problem that I've been having at 2sites now; the client computers show repeated syslog entries ofEvent 4201 - The system detected that the [XXX adapter name] was connected to the network,...
I have a couple of Aironet 1100 series APs that should be connecting with a Cisco WLC 4400. Started with one that was seen but not set to the correct radio setting but the WC didn't have a place to reconfigure that setting which I could see. So using...
Hi to all,I've reading a bit about this and i'm a litle confused.We have a 5508 Wlc with many 1140 aps. And i would like to know how many clients can handle each access point.On this device there's a param under wireless-802.11a/n 802.11b/g/n - gene...
I think i may already know the answer to this, but as a last ditch attempt, does anybody know if there is a way to recover a WLC password?We have a few WLC 2100 series controllers with quite complex configurations, SSID's spread accross large number ...
i have two network seprated by firewall one side network is with WLC and 2 AP if i want to put 3rd AP in a zone which is behind the firewall what configuration is required and how AP will join WLC.Thanks
I have an AIR-AP-1252AG-A-K9 AP connected to a WS-C3750-48-PS-S and I am getting an error:%CDP_PD-2-POWER_LOW: - NON_CISCO-NO_CDP_RECEIVEDWhat do I need to do to clear this error. The STATUS LED blinks RED.
Hi,Can someone provide me detailed description on how WLC Radius Server Load balance works.Becuase, I encounted a problem of User Authenticated with the 1st Radius Server, but Accounting Records are actually on 2nd Server .Any response will be very a...
Hi there,I already have 1 WLC 5508 over production.I need to implement a secundary WLC and a wcs to the network.Whats is the best way to do it ?Im planning to install WCS, add the primary WLC to the wcs, and then the secundary.As its my first WCS ins...
