Hello, i want to ask if there is a way to limit the speed on Guest access for every user thanks
Hello, i want to ask if there is a way to limit the speed on Guest access for every user thanks
We have Symbol Pocket PC's that support WPA, but NOT WPA2. Can I implement WPA on my Cisco Aironet 1200 series AP's? The model number on my AP's are: AIR-AP1231G-A-K9I need to do WPA-personal (PSK, i think), not WPA-enterprise.Any help would be gre...
Is there any way to set the RRM parameters such as max power or channel selection for AP's. I would like to have the network set their own settings but would like to set a max power for the AP's
Doing a search on Google to find the purpose of the Order bit in the 802.11 header (subfield of the frame control field) only provides a generic (not helpful) explanation of how it's used for stict ordering of the fragments/frames. Fine, but what doe...
Hi.Anyone got the attached screen? I am not able to setup a simple root and non-root link and suspect from faulty hw. I would appreciate any sample config to test the link. I tryed with config from othe two same APs but not working (old used 12.3 a...
Hi All,I want to setup a WLAN that uses EAP-TLS.WiFi PC <-----> LWAP <------> WLC <----> Radius ServerUnder the Layer 2 tab for security on the WLC what option do I use for the following :-Layer 2 Security (I am assuming WPA+WPA2 as that what the lap...
I get in our logs "Received LWAPP packet with invalid sequence number". Does some one know what this means?
We have a number of autonomous 1200 series APs running 12.3(8)JEA1 IOS. What I want to know is how, or can I, monitor the number of users and the data rates being used on each AP w/out a controller? We have Cacti and were curious if this informatio...
So if someone is not logged into their domain, and they are just using a local account on a laptop, what happens when they try to get on an 802.1x wlan? Does it prompt them for user/pass?
We run several clients on SSIDs that are broadcast. Occasionally the SSIDs disappear from the list of available networks for our Intel clients but they still work for Oddessey and Microsoft. We have to bounce the APs or controller to get them to com...
Hello,I have recently started to get a lot of âCoverage Hole Detected for AP03 whose Base Radio MAC isâ¦â¦.. Number of Failing Clients 1â across my company site, a couple of mins later the trap log reports âCoverage hole cleared for Base Radi...
Hello,few questions regarding the H-REAP mode:1. How many H-REAP mode AP's can be configured for 1 location?2. Does H-REAP AP need some special settings from the network side? no NAT, static IP etc.?3. which interface does the H-REAP AP should "see"?...
Hi,I'm trying to solve an AP 1130 (in H-REAP mode) that didn't manage to connect to the controller (WLC4402):%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - WLC4402)%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no m...
Hey all,I've been trying to discover for a while how primary and secondary RADIUS servers work on WLC 4400s. If the primary RADIUS server goes down, and the secondary is used, at what point does the controller go back to the primary once it's back u...
I have a 64 AP with WLC install, 56 APs we can see in the WLC, 8 we cannot, the 8 APs were visible and hour ago, WLC can ping APs. Reboot APs, same results, What could be the cause.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-16-2024 12:50 PM | ||
08-15-2024 04:04 PM | ||
07-25-2024 07:13 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM |
User | Count |
---|---|
19 | |
12 | |
5 | |
4 | |
3 |