Wireless

Hi guys, Is there any recommendations about the size of the subnets used to communicate the supervisor 720 with the wism. I think I will waste address, for example, if I use two subnets /24 for service vlan e ap-manager. Thanks in Advanced, Andre Lom...

Hello everyone, I just want to get everyone's opinion on which way to go for a wireless controller. Basically, I am deploying a wireless N environment. As a result, I either have to get a 4400 series controller or a Cisco 2821 router with the control...

How do you handle per phone user / password authentication when using EAP-FAST? Do you create 1 credential per user when you distribute the phone or do you have a shared credential for all your phones?

Hi all,I am having some issues connecting an Intel 5300agn nic to our Wireless G access points with WPA2+Peap.Can the 5300 connect to 2.4ghz G or is it built mainly for 2.4 N on the 1250N ap, which it can happily connect to.Thanks.

Is there a way to watch what Lightweight Access Points are connected to a controller? We have a large environment, and current have 81 lightweight access points spread over 4 different controllers. I can ping the access points with their static ip ad...

We have a lot of 1252 AP, they registered to a 4404-100, if we enable the 802.11n (a/n and b/g/n) we didn't seen it from the clients. The APs have a power injector (AIR-PWRINJ4)- AP Sw : 5.2.178.0- 4404-100 Sw 5.2.178How can we use it?

I bring in an autocad drawing to png and type in the Horizontal & Vertical dims. When I go to look at the maps to place APs, the map is all squished. When I try to alter the dimensions I tells me I can't be bigger then the parent building. Here are m...

I have a bunch of standalone AIR-AP1231G-A-K9 running c1200-k9w7-mx.123-8.JEC2/c1200-k9w7-mx.123-8.JEC2 which is currently setup for guest and company ssid. The guest I don't care but for company, it goes back to a Microsoft IAS radious Certificate A...

Hello everyone I hope if anyone can help me.a Building has 3 companies (A,B and C) and I have one WLC in each company there is 3 AP I want to configure WLC whereas any AP in company A cant communicate to other AP in company B and C and the same to al...

I have 3 access points that I recently converted to LWAPP. After the conversion, all 3 AP's are now MIA - no sign of them in WCS or on any of our controllers. I can trace them back to the switch that they are directly connected to and they do pull a ...

We've got a pair of PIX 525s in active/standby mode, plus a pair of VPN 3005 concentrators (one active, one redundant using vrrp) for IPSec VPN connections (both LAN-to-LAN and Remote Access, 3DES). I'm trying to generate a proposal to replace all 4 ...

Have any of you tested the LWAPP 1250 AP with a media converter or combination media converter/PoE injector. - Just wondering if there are any that work OK. I don't need 56 volt PoE since I will only have one radio module installed, but I can't see b...

I have 2 controllers each are part of a different module (WiSM) and both keep rebooting (not at the same time) , both module are located within the same chassis.When this started i had version 4.2.99 so i upgraded to 4.2.176 but it keeps doing it.I a...

I am tasked with trying to implement wireless for a client using wpa2-enterprise tied in with Microsoft IAS. Everything I am reading so far points me to the requirement for using certificates. A lot of these computers will either be running out of th...

Here is my problem. I recently installed a 1130AG wap in one of our remote offices. There are three computers in this office, all wireless ofcourse.Two of the three computers stay connected, and one drops every few minutes and connects back up. I hav...