Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Labels

Forum Posts

Hi all!We created two VLANs namely VLAN1 (on Dot11Radio 0.1 and Fastethernet0.1 which is native VLAN)and VLAN2 (on Dot11Radio 0.2). We gave ip addresses on Dot11radio0.2 and Fastethernet 0.1 which are in different subnets. We can not reach the Dot11r...

n.karaca by Level 1
  • 972 Views
  • 3 replies
  • 0 Helpful votes

Help - I have assigned an IP to eth1 which I would now like to change. Unfortunately nothing happens when I issue the command. It does not even respond to the 'interface eth1 down' command. I am running WLSE 2.13. I've reloaded several times with...

mikeb by Level 1
  • 409 Views
  • 1 replies
  • 0 Helpful votes

I admit I don't completely understand mobility groups. I need to add a server on one of the wireless networks. I can't seem to figure out if there is a way to configure a port on a 6509 to be in the same wireless mobility group. Thanks.Edited: No nee...

mgross by Level 1
  • 329 Views
  • 1 replies
  • 0 Helpful votes

Hi,we have got two ofices in different area. We decided to connect them with two AP's Aironet 1310 with mode point-to-point bridge. We have voice traffic over this wi-fi channel. If we use IOS 12.3(4)-JA we have noticed many errors in the logs 1310 s...

v.istomin by Level 1
  • 353 Views
  • 1 replies
  • 0 Helpful votes

I had 6 LWAPP AP's confgiured with primary and secondary controllers. I shut down primary controller - 5 AP's swapped over to secondary controller - 1 couldnt join. Turned primary back up and the 5 moved back and the 1 LWAPP AP still couldn't join. ...

I have my wired network (w/DHCP and vlan scopes). Attached to the wired network is a 1400 series bridge1 connecting to another 1400 bridge2 (via 802.11a). Bridge 2 connects to a 1200 Access point via a straight ethernet connection. I want to use VLA...

We have wlan 4400 controllers in our lab and would like to configure management authentication through out Tacacs/Acs infrastructure. Unfortunatly, I only saw options for locally defined users on the controller itself which will surely cause issue w...

quesne02 by Level 1
  • 680 Views
  • 4 replies
  • 0 Helpful votes

using Funk radius server and MD-5 challenge I can assign users to a vlan on my switches. But when I tryto assign vlans to users on AP via the radius serverit fails. All SSID are mapped to vlans and encryptionfor all is WPA/TKIP. The authentication st...

g.peart by Level 1
  • 1766 Views
  • 11 replies
  • 0 Helpful votes

I had a reauthentication problem which was fixed by the hotfix reported on http://support.microsoft.com/?kbid=885453. The hotfix repairs a compatibility issue between MS PEAP and "third party radius servers" (i.e. ACS). Unfortunately, the patch gav...

We have a machine intel core duo macbook pro machine running mac OS X 10.4.5. We are using encryption IEEE802.1x WEP with PEAP-mschapv2 authentication. The authentication passed. And a show dot1 association all-clients have the correct ip address for...

pppyyyppp by Level 1
  • 674 Views
  • 5 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card