Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,We have:6 1130AG - 12.3(8)one ssidall 1130s are on the same vlanencryption mode wep mandatoryDo we need WDS to allow IBM thinkpad to roam freely between 1130s?Thanks in advance.
Could anyone tell me about the fips kits and its use?Wen i used config tool for NAC and AP this kit comes as option to choose.Thanksswamy
Hi,i'm trying out an 887w router but can't for the life of me figure out how to get the wireless running 802.11b. Before you ask why its so i can get PDAs connected. thanks in advance Charlie
I am trying to upgrade to version 4 on my 2006 LWAPP controller.I am trying download AIR-WLC2006-K9-4-0-206-0.aesto the controller.It APPEARS to download fine but I get these two messages after the download completes:"TFTP Failure while storing in fl...
Hi,i have a AIR-AP1230B-E-K9 running 12.3(8)JA2. when one of my clients who has not configured any hostname on his laptop connects to the AP using the inbuilt wireless card, it can be seen that the clients hostname (in the association list of the use...
I am attempting to configure a 1231G to use PEAP Authentication. I am using Windows 2003 Server running IAS as my RADIUS Server. The AP has been configured and is communicating with the IAS Server, but all of the authentication attempts are rejected ...
Hi All, one Customer uses WCS 4.0.81.0 /w Location for Management. It seems to be not possible to show ALL detected Rogue APs on a Map, only one selected AP from the List. Is there a possibility to show all Rogue APs at on Map? Regards, Michael
Hi,A have the following scenario:5 vlans configured on my AP, 3 of them use PEAP to authenticate users (not computers), I'm using ACS 3.3.3 connected to my Active Directory.The thing is, How can I filter access from one SSID to another if I am using ...
SSID is not being set to be "hidden" for the WAP in our office. I want the SSID to be hidden and not visible as we do want to control the access from being stolen by the contractors in our office. Please suggest how to have the SSID hidden. We can't ...
I am kind of lost on this:If I am using LEAP as authentication mechanism, am I automatically using 802.1x? On my Windows XP, I look onto the "Aironet Client Utility" I see no information on 802.1x there.I have configuration of access points handy her...
I have a problem whereby a particular wireless client is choosing to associate with the root bridge rather than with a nearer non-root AP which has a much stronger signal. As a result, the client is experiencing dropouts due to the poor signal to the...
Hi,I am running ACS Release 3.3(1) Build 16 and am having a weird problem with our wireless users.A few of them get kicked off the wireless network after a few minutes and I look through the logs and get the error "User exceeded max sessions" but the...
Can someone provide me with a sample config of more than three ssid's being configured on a 871W. I can get two ssid's to work but not more than that. Here is part of my config.Thanks!interface Dot11Radio0 encryption vlan 1 mode ciphers tkip encrypti...
hii wanted to increase the security on my 1121G accesspoint by enabling wpa2 with aes encryption. in a test environment i set this up and i configured my wireless client to connect, my wireless client (ibm thinkpad t42p with 11a/b/g Wireless LAN Mini...
Hi, I'm having trouble getting the AP to work. When I check the status of the AP in through the Web browser on the 4402 controller the "operational status" is showing down?? Does anyone know why this may be? Hence my wireless laptop can not see the w...
