Wireless

Will the coverage of an access point say AP 1020 with ANT 3213 in North America be the same as in Germany considering the transmitter power in North America can be set to 100mW max and 50mW in Europe max ?

I have been assigned a wireless LAN project and need some help with where to start hardware, number of access points and how big the footprint is from each of the WAPs and how many WAPs each of the WLAN controllers can support

I an a ccnp, but want to become certified with wireles, cause in my country cameroon we use mostly wireless. so please, can you give me good books and tell me where i need to start from. thansk for your help in advance.

Hi there,I'm trying to force WLAN clients to reauthenticate after a certain time by sending RADIUS attributes (session-timeout/termination-action) to a WiSM module after successful 802.1x authentication.This does not work. But configuring a reauthent...

i want to setup a vitual private network to monitor road trafica in a capital city of Ghana. i want to have a base station where i can monitor all the remote site from.can any one tell me all the equipments i need to make this project successful? i w...

I have 30 ap 1230 in my network with ios version 12.3(4). I use cisco client e not cisco client with leap and peap authentication and all work fine.I have upgrade one access point 1230 to ios 12.3(8) and all my clients are ko.they not receive any wir...

Hi all,could someone explain me howand in which phase AP allocate IP addressfrom DHCP pool for authenticated client?We have many APs configured with WPA and radius authent. but I dont know where it is said that AP should alocate IP addressfrom concre...

I'm trying to setup a site with two Aironet 1130AG WAPs. These are being accessed with Acer tablet PCs running Windows XP Tablet 2005. I've tried configuring both WAPs as access points with the same SSID, and I've tried configuring one as a repeater ...

I'm trying to configure a new WLSE. I try to connect to the console port on the back of the box with a x-over RS-232 DB9 cable. My Hyperterm is set for 8-N-1 flow control:none. No monitor or USB ports are plugged in. I don't get any response. I've al...

We have a 2000 wireless controller with 4 1240 access points connected to it. The users would like to run their current non-cisco wireless network until all testing has been completed with the new cisco wireless installation. We have their old wirele...

Hello,we got a WLC 4402 running on our Network and use 7920 IP Phones. Under Wireless-> Rogue Clients i see many of the Ip Phones as threat.Actually we have many of EVENT ID 3 in the Callmanager which says that the devices unregister and some time la...

I have cat6513, sup720 (ver 12.2(18)SXF3) and wlsm (ver 2.1(1)). I have L2 and L3 vlan 11 interface (ip in same subnet as wlsm admin vlan) configured on sup720 and "wlan module 2 allowed vlan 11"I can ping the wlsm from the sup720 (and vice versa) bu...

I'm having problems adding 4402 and 2006 WLCs to WCS using snmp v3 credentials. Using auth=MD5 or SHA and Priv=DES. Snmp v1 or v2 works fine, but snmp v3 usually requires 4/5 repeat attempts or rebooting WLC after adding snmp v3 credentials and even ...

My company had an incident recently. A 'user' installed a WAP at a remote area on a flat portion of our network. The WAP's DHCP server started handing out 192.168 IP's. This caused a great deal of chaos. Problem detection was compounded by the fact t...

HelloI seem to be getting a rogue error message that says my 2 WLSM's standby address is trying to manage my WAP's. But looking in the WLSE and that address is not in the manage/unmanage section so not sure where the information is coming from!!Any i...