Wireless

Hello everybody,We are looking for a document about how to setup PEAP with Windows logon to domain that it also has logon script or group policy enforcement from the domain controller machine.We have seen the following topic but we could not access t...

Hello there,I am a newbie on wireless technology. I am reading wireless controller document. I am confused about 802.11 bridging and 802.3 bridging. What is it? What are they different? I understood that the controller always bridge between 802.11 an...

Hey I wander if anybody can shed some light on a BBSM issue.In a wireless environment, Is it possible to configure multiple pagesets (and hence splash pages) for users associating to a single, common access point ??Documentation seems to indicate tha...

do cisco2000 installation require win2000 professional or win2000 server ?

Hi, I'm testing a AP1231G firmware 12.3(8)JA2 with 2 SSID.SSID1: WPA/PSK (TKIP)SSID2: WPA/Enterprise (AES)After booting up the AP, i use a notebook to connect to SSID1. Then use another notebook to try connect to SSID2. But no other notebook is able ...

Hi, This message was just logged by one of my 1100 APs. %SYS-3-CPUHOG: Task is running for (0)msecs, more than (2000)msecs (1359/7),process = RADIUS.The only time this device uses Radius is to authenticate to a WDS-AP.The AP seems to be running fine ...

hello to all...i have connectivity like this:Host1---AP-trunk---Cisco2950-trunk--LinuxVLAN2 | | Host2--- |VLAN3i have created 2 vlan on AP... and fastethernetport of the AP is connected to the cisco2950 and cisco2950 is connected to the Linux server....

I have not been able to get WiSM controllers on 4.x code to detect a wire-side rogue with open auth (Cisco AP and Apple Airport Express). It did find the open Airport AP once when running 3.x code, but has not since the upgrade.Has anyone succcessful...

I have a WLC 4400 in a remote site and I need to reset it to Factory-default. The service-port is connected to a switch and it can obtain an ip-address from it. I don't have a remote console access. Is it possible to do the inizial wizard configurati...

I've confured a new site with 4 radiobases AIR-AP1231G-E-K9 c1200-k9w7-tar.123-8.JA2.No Vlan, WPA, TKIP,(The same config as many other sites).Authenticating to a central Radius.My problem is that I cant move around whithout losing the connection. I h...

After AP1232 convertion from IOS to LWAPP -> following error Message*Mar 1 00:00:44.216: %LWAPP-5-CHANGED: LWAPP changed state to JOIN*Mar 1 00:00:50.217: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response *Mar 1 00:00:5...

When i add ip address 10.100.100.1 255.255.255.0 secondary to interface Bv1 and i type show running-config i can't see secondary ip address.Why?Many Thanksap# sh verCisco Internetwork Operating System Software IOS (tm) C1200 Software (C1200-K9W7-M), ...

I'm hoping someone can lead me to the right document or show me some example config to have my 871w use MAC address authentication. I currently have it setup to use WPA successfully, but for added protection, I'd like to use MAC address authenticatio...

Hello,I use freeRADIUS to authenticate WLAN Clients. Traffic is encrypted with WPA and clients are authenticated with LEAP or PEAP.The AP 1220 with IOS 12.3(8)JA2 works well and the configuration is the same for PEAP and LEAP.The value "Session-Timeo...

Hi,I was wondering if anyone knows if it is possible to vnc to remote vpn clients that are assigned an address from a client IP pool defined on the pix.The remote clients are using cisco vpn client, the access-list is a dynamic acl downloaded from a ...