Hi, I intend to apply ACL on WLC to achieve following - Only admin should be able to logon into WLC from his IP- Only AP's should be able to join WLC from their specific IP pool 10.202.x.x/24 (no other IP pool should be allowed from where AP ca...
Forum Posts
Hello!Just started my very first Network admin job and the first thing I'm diving into is complaints about WiFi performance.We have a bunch of Cisco Meraki MR33's serving a wide office area. The main complaints come from an area where users are packe...
Hello,Just started my first network admin job and need advise! One thing I immediately notice here is that people often complain about WiFi coverage/speed/performance etc and it's difficult to pin down whats what.The main office is also currently go...
Dear all,My question is maybe a little bit newbie, but I would like to turn on Meraki roaming. In our office, we have many devices which support this feature BUT few devices which not...and I am not sure if the Meraki roaming will have a negative eff...
Resolved! Power Consumption of WLC 5520
Hi All , I need to find information about Power Consumption of WLC 5520 but I not see the information. Please help me .
Resolved! Issues with 8.10.181.0 and 3802s
Hi All-I just upgraded my 5520s to 8.10.181.0 in anticipation of deploying some new APs. 8.10.181.0 appears to be the only version that supports the 9120. It did no go well!We have pairs of controllers. I upgraded one to 8.10.181.0 and left one at...
Hello,I am a Junior - Intermediate level Network engineer.I am currently trying to configure our 9800 WLC management Ethernet ports purely for SSH purposes. We have 2 WLC 9800-40 running HA.I am looking for guidance or ideas on how to configure the p...
I'm having a rough time getting my new CBW240AC set up. I can do the zero-day configuration just fine, and after the automatic reboot I have wireless network access and can manage the wireless network. However, when I power off the access point and...
Hi, we are fairly new started with DNA Center and have been using Prime Infrastructure in parallel. What we see in DNA Center version 2.3.3.6 on 5520 WLC using 8.10.171 with 9120 APs that clients show broadcast rekey failed, we are using a WPA2 PSK b...
HI,We have several (12 to be exact) MR42 devices. In specs it is stated that those support BLE beaconing and BLE scanning.Scanning and Beaconing enabled via meraki cloud dashboard (IoT Radio Settings) , but no sensors with BLE enabled (non cisco mad...
Resolved! 802.11b Global clients threshold
Hi In mobility express GUI in RF profiles "Maximum clients per radio" limit is set to 200but in cli it is showing below.(Cisco Controller) >show advanced 802.11b profile globalDefault 802.11b AP performance profiles802.11b Global Interference thresho...
Hi All, There's an issue with AIR-AP1832I-D-K9 model ap not connecting to the WLC. When the AP connects to the WLC it goes through the discovery process 1st and joins then immediately shows DTLS teardown. In the same WLC AIR-AP1832I-E-K9, AIR-AP1832I...
Is it possible to have multiple primary 9800 WLCs configured to fail over to the same shared HA 9800?
Have tons of 9120's on the 8540 but the 9130 AP doesn't make it past the Discovery. I haven't gotten a hit yet on a search.[*10/20/2022 17:55:58.7157][*10/20/2022 17:55:58.7157] CAPWAP State: Discovery[*10/20/2022 17:55:58.7164] Discovery failed 7 ti...
I have 2 x 1gbps upstream LAG to Provider and it is heavily utilising the following on the ports:Port 1 - 100% with dropped packetsPort 2 - 2% UtilisationCisco's default hash algorithm for Port-Channels appears to be IP based and therefore will utili...
