Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have a MS225-24pw, I also have a MR76 in the same locations.I want to add a point to point It a TP-Link CPE710 I am putting this device on the roof facing the baseball park. On the other end I have a ms120-8FP and it has MR76 also to get data I wil...
Is it possible to use DNA Spaces without DNA Center or Prime ? There does not seem to be a nice way (read , any way) of getting maps in DNA Spaces without those two. Did I miss something ? Thanks Thomas
Resolved! MX450 Performance capability
My customer currently has 2 HA pair of MX450 acting solely as wireless concentrators. Due to a DC move they have questioned can these be consolidated into a single HA pair. They have approximately 600 AP's with each AP supporting on average 5 tunnell...
Resolved! Wireless AP Bridge commands
In every sample of configuring wireless access points, including Cisco documentation (notably the older Aeronet ones), I find the following lines to be configured on the bridge group which includes the radio interface: bridge-group 1 block-unknown-s...
I am new to configuring these 9800 controllers. I have experience with a 5200 series controller and I am aware that the firmware is different. I am in an ongoing battle with DHCP working but not as intended or not working. I am trying to configure th...
Resolved! 9800 HA N+1 Retaining AP Tags
We are in the process of converting to Cisco 9800 controllers and are testing the HA failover in a N+1 deployment. When AP's are failed mover to the secondary HA controller, they are falling into the default policy, site, and rf tag group. On the H...
I've noticed some odd behaviour for web auth ("global" parameter map). This applies on IOS XE 17.9.3 and 17.9.4a, and possibly on other versions too.If I use the web GUI to define the banner text as "Welcome", then save my changes, this gets truncate...
In some release notes for APSP it states that for example SP2 contains all the fixes of SP1, so you only have to install SP2. But I cant quite seem to find this "wording" on APSP release notes for 17.9.4. Did it change ?
Resolved! client exclusion of WLC
Hi I would like to ask that is wireless client MAC address has been assgin to Excluded Clients, does the WLC will ignore the "auth request" during the exclustion period? Frankie
Resolved! about CAPWAP data flow
As I know, a WLC receives a user packet from AP via CAPWAP, it will remove CAPWAP header, translate L2 header and forward it to a GW. Here are my questions and do appreciate any input from you. Thanks!Q1. If a WLC uses trunk port to connect to L3 sw...
Deal All,I had recently set an 3802 AP as a Monitor AP to troubleshooting signal issues.I can ping the monitor AP but could not webpage to it to check the logs it capture.is there any alternative to check out the logs ? from the 5508 WLC ?Any help ar...
I'm trying to upload new software to scces ponita. After running the update, an error appears.ap-type mobility-express tftp://10.10.100.20/AIR-AP2800-K9-ME-8-10-190-0.tarImage transfer complete.Image downloaded, writing to flash...do CHECK_ME, part1 ...
Hello,C9120AXI-B APs are joined to WLC 9800-L with US country code.I tried to join several APs AP3802I-E-K9 with UK country code to WLC 9800-L. But failed. Reason is Regulatory domain check failed.When
Hello All,We have an important problem. At our branches using Cisco Meraki, we get 30% unsuccessful certificate authentication results. When we look at the logs in Cisco ISE, we get an error as "5440 Endpoint abandoned EAP session and started new ( S...
Hi All, I am tying to get my new AP AIR-AP1562I-E-K9 installed in our airport and its mounted and learning in switch CDP neighbor but its not getting registered in WLC switchname#sh cdp nei Gi1/0/48 det-------------------------Device ID: AP3473.2DA2....
