Wireless

I am using Linksys Etherfast wireless ap + cable/dsl router (model BEFW11S4). I want to use cisco 340 to repeat wireless signal. My Cisco NIC changes from Linksys to Cisco wireless signal but it looses IP configuration. Linksys is my DHCP server as ...

Does anyone have recommendations for positioning Access Points (we have 340's) for best throughput and simultaneously best area coverage for our laptops in a one-story building. I'm getting only about 2.8-3.3 Mbits/sec real TCP throughput (with 128 b...

sminhaz@rediffmail.comDear Sir , I am Planning to setup of a Network through wireless, But I am Confuse which product I will use .. CISCO Aironet 350 Series .. but I have to give a setup in 5 place in that case one station is in Middle & rest of the ...

I've got a customer using Symbol 6948 clients w/Cisco 350 APs running 11.07. It appears that the Symbol clients seem to always want to go to the AP that's on Channel 1, even though there's much closer APs that are on channels 6 or 11. All the APs are...

I expeirience problems with a wireless link (Point to Point), while running a large amount of ICA sessions. When reaching approx 600 packets/s on the link, the radio starts throwing packets, resulting in "frozen" ICA-sessions, and users "throwed out"...

Hi all,In warehouse or manufacturing environments where there are a loarge number of clients and a large number of APs (350s in our case), the 350 seems to wait until the quality of its association is really lousy before it tries to roam to another A...

I wnat to connect 5places by cisco wireless product all are 40km in distance . If i use point to point then it is ok but if i want to use multi point to Point then what are the product I have to use can any one help me ... I am looking for it badly.....

Hi -- We are using Aironet 4800 AP's thoughout our factory. I have been told that you should not attach different antenna's to the same AP. In other words, do not attach a dipole antenna on one side and a patch antenna on the other side(both should...

I am setting up an outside network to be used mainly by handheld devices (Ipaq using the the PC card adapter). I am thinking of using the Aironet 350, but I need more range than 2000ft. So, I was thinking of using the Air-Ant4121 to extend the rang...

With all the talk of 802.11a products on the near horizon, I'm wondering about Cisco's plan for this technology. Will there be support right away for speeds less then 54Mbs? (I hear the max will be at 90ft). (Are other speeds in the standard ?)Is Cis...

I'm trying to setup a 340 Series Bridge to do dynamic WEP. The device is set to be an access point, but I still don't see the option.The bridge is running firmware V8.24.Is this possible? Thanks

I am interested in a bar code scanner that will run Windows CE, be programmable using something like Java, VB or C and supports Cisco Aironet Dyanmic WEP. I would like to run Cisco Secure ACS against my Windows 2000 A.D. and authenticate the user of...

Can anyone help me with this?I am getting CRC errors on a few of my bridge access points that are in the range of 90 to 200+ CRC errors every 10 seconds. This is only on the radio side, not the cabling side.I have a 4th floor office and am using bri...

I am looking for documentation regarding traps for mainly the radio side of 340 & 350 Bridges and WG Bridges. Especially signal strength / quality and connect rate. I have some MIBs loaded, but the AP MIB's are all that appear to be available for thi...

I am confused, when using Leap does the Wep key get changed each time the client device roams? What kind of time delay does this cause. Does the Access Point give out the new key or do you have to go all the way back to the Radius server to get the ...