We have a network of Cisco AP1562I running mobility express. I wanted to see if we can add a Cisco 9120ax to the network and run in Mobility Express as a subordinate AP. Plus keep the AP1562I as the the WLC. As the 1562I are end of sale.
Forum Posts
Resolved! Packet Drops and Low Bandwidth
In our company we use WLC Type Cisco Catalyst 9800-L Wireless with Software Vesi 17.6.4, and for AP type AIR-AP2802IConfiguration QoS 15Mbps per Client, not per SSIDThe problem is that when there are more than 50 clients connecting to the AP, there i...
Hello, I need some advice, I recently purchased a SIM card for a secondary circuit for a Cisco C1111-4P-LTE router, but unfortunately, the ISP is assigning a private IP to the Cellular 0/2/0 interface, which seems to be undergoing NAT on the ISP side...
I have an inquiry while operating the network. The customer doesn't have any symptoms on the wire, but the wireless internet is very unstable, so we're checking it.In wireless firewall settings, there is a Peer-to-peer blocking rule in the Layer 7 [B...
From the 9800 CLI interface, how do I edit the 6ghz radio on one specific 9166 AP to make the following changes:Change role assignment = Client servingChange band selection = 5ghz
I have a multi floor building and want to implement a single SSID across all floors. Each floor will have about 10 APs. The building's network has been designed to route from the access layer. Meaning there is a L3 boundary between the access layer a...
Resolved! AP2802 loop during boot
Hi, We have a Air-AP2802 ap that is trying to connect to a wlc(set up on another 2802 Mobility Express). Software on the AP that is set up as the WLC is 8.3.132.0. When connecting to the AP via console it seems like it get IP from the dhcp and di...
Hi, Is there a way to define burst data rate on WLC 9800? We are migrating AP from WLC 8540 to WLC 9800 and on WLC 8540 override per-ssid bandwith contract is configured like in the attached img. How can we recreate that on WLC 9800? We can set qos ...
Hello team,An iphone user not able to connect to guest wifi.authentication method : mac filetering and aaa server is ISE.user is getting profiled and the authentication page is not popping up for the user.And the issue is faced by only apple users an...
How to find BSSID of AP's WLANs directly connected to C3850 I know for Cisco wireless controllers, the below command shows the list of BSSIDs for that AP,show ap wlan [802.11a/802.11b/802.11-abgn] <Cisco AP> Can someone help me with command to list t...
Hi, we have one main wireless controller 55xx and one mobility anchor controller 55xx for some WLANs (SSIDs). Now we need to upgrade the main wireless controller OS to support the latest catalyst 9K access points, but anchor WLC os is still 8.5.x, do...
This is why the "new" roaming tab on the client view is so good.See how my notebook roamed from an AP with -43 dBm of signal strength to an AP much further away with a signal strength of -67 dBm (a number closer to zero is better)?This is a 100% clie...
I have a quandary. I have 6 MS access points we just setup. 5 of the 6 work just fine. One allows us to connect but it continually says no access. We are not doing PEAP/EAP or any radius configurations. We have pushed a profile via intune to have the...
I’ve got a challenging environment that I’m looking to improve Wifi coverage and capacity in. It’s a parking garage for city transit buses. The building is somewhere in the neighborhood of 240 feet across and around 600 feet long, but the flat roof i...
Hello, I am moving all my on prem servers remotely. I have created a new NPS installation on a new server. I then exported the NPS configuration I had on-prem and imported it to the new server. It starts up fine and I can see all my access points und...
