Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
HI Everyone !!I need to cover a wide-area with only one Access Point (Aironet1200) but I'm not sure if I can use an Outdoor Omnidirectional Antenna (Air-Ant2506) with Access Point because Cisco reccomended to use with Bridge. Could you help me ??Than...
Hi all, I have a customer that wants to install the BBSM at their site so that they can sell wireless broadband. The question I have is about the billing portion. They want to make it so that the person can input a credit card and buy access. The whi...
I am trying to set up a 1310 bridge link, and currently have the devices set up in my office. I have not recieved the external dish antennas, so I am trying to use some 2.2 dB dipoles just to get them configured. The problem I am having is that they ...
hi!customer has configured 2 vlan's on his access point (vlan 1 = native and on other: vlan 9), each vlan has been assigned different SSID and WEP key's.laptop users can associate to both vlan's depending on which SSID and correct WEP key they use. h...
I have an AIRONET 1200 Accesspoint with 802.11 a,b,g (2 external Antennas for 802.11g) and 2 Clients. One Client with 802.11a,b,g and the other one with 802.11b. The scope with 802.11a is very bad, only one door or wall is enough to disturb the conne...
We're just beginning to test wireless and wanted to use MS-PEAP as the authentication method. Unfortunately we found that when we enabled PEAP on the adapter (Centrino on IBM laptop w/ WinXP SP1) we got the dreaded Blue Screen of Death. It blue scree...
Can an 1100 AP support trunking? Here is what I want to do.The switchport is configured for a specific vlan so everything in the wireless cloud is on that vlan currently (LEAP/WEP). I want to setup a seperate open Guest SSID vlan and put it in the sa...
Any help will highly appreciatedCompaq IPAQ Pocket PC 2000(WINCE 3.0).. 3630 I am having problem bringin it on wireless network...i just got a CISCO 350 client adapter for this pocket pc...I got it on the wireless network .. but i get intermittent pi...
Having had the IOS upgrade fail on me I cannot now get the AP to reinstall the software using the method outlined in Cisco documentation. I can access the unit using the console where I get the ap: command prompt but when I try and ping from the tftp...
I have a problem with users associating with one AP. I get this message:no address for get_serversometimes I'll have that message 4 or 5 times in a row.
Hi,I have ACS 3.1 set up on a Win2k member server. I have an A, B and G series access point. I keep getting this message over and over.Here is the config...Building configuration...Current configuration : 2079 bytes!version 12.2no service padservice ...
Any recommendations for a usb wireless adapter which supports tkip encryption with Cisco's leap. I am considering the Dell 1300. Does Linksys support this configuration? Any others?
Hello,When we were running AP1100's with 802.11b our ipaqs h4150/5550 with buildin 802.11b were connecting fine. Then we upgraded our AP1100's to 802.11g. Since then our h4150/5550 are connecting, but do not get an IP-address anymore. It does not hel...
Can someone tell me what this entry in the log indicates? Is there documentation that explains these and similar log entries?
Currently we have several 1200ap's deployed using LEAP with only one Cisco ACS. Most of the AP's are in one building with the ACS on the same network. A few remote offices have only 1 ap which has to authenticate back to the central ACS which then ha...
