Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have setup WLSE 2.11, and everything is working great. The rogue detection works fine, but appears to be picking up bluetooth phones, mice, printers, etc... I don't know what else it could be because I don't see how one AP in one dorm could detect ...
Hello all,We have a user on the network that is unable to connect to WiFi.When testing on external networks, it connects normally.I checked the events and found the client fails many times during association, but then I have some events that he succe...
I have a bunch of 3500 APs that I want to convert to lightweight in order to connect them to a WLC. I know that the series is out of support, but that's what I've been provided for my project for now. Been trying to find a place to download the image...
Resolved! Use SSIDs with VRFs in C9800
Hello All, I have a C9800 anchor in a DMZ connected through EoIP with multiple front WLCs.From a WLAN perspective, multiple "Guest" SSIDs are deployed, each is tied to an interface on the anchor. As we have an external DHCP server, I have being tryin...
I am using AP 1852E using mobility express mode. Can Cisco's new APs join it? or where can I find documentation on what AP models that can join AP1852E? Thanks
Hello,I'm slowly getting a little better at configuring the Cisco AP via the WLC. Now I'm in theprocess of setting up a guest WLAN in addition to the internal WLAN. Now my questionabout it:1. How do I configure the switch port where the AP is connect...
Hello,I have the following problem, if I have to disconnect the WLC 2505 from thepower supply, it loses the time. It is then always on 01/01/2000, even thoughan NTP server is entered.Is there a way to check that the NTP server that is entered on the ...
Hi all,I'm pretty new to networking and we have an office move where the networking person just left the company. I need to help move 1 Meraki MS120-8LP 3x Meraki MS120-48LP switches . Is it just as easy as assining the new IP addresses to the Meraki...
Hello everyone,I am facing an issue with our Cisco WLC series 5500 controller, the previous network administrators did not leave any documentation behind, and I am unable to contact them for support.I need to build a new Guest WIFI with a email verif...
Hi I have lost username Cisco and Password Cisco after a factory reset on AIR-AP-1800S-A-K9, can not access sensor, how to fix it
Hi, I had one problem which I found bypass solution, but I would like to share with someone, as I don't want that someone is wasting time as I did troubleshooting the issue.My case was that I have 15 APs AP1832i set to Cisco ME, so 1 acts as a call i...
I'm hoping for some help here, I'm trying to fire up a new Cisco 9800 WLC for first use, and for some reason I cant get the DHCP discovery from the client to be forwarded to and external DHCP Server. I enabled the DHCP Service from the CLI, also ena...
Helllo everyone, I have an issue, our AP is VID 07, as check from Cisco Wireless Solutions Software Compatibility Matrix - Cisco it seem that it is not able to join the WLC 5520 version 8.10.130.0, unless we upgrade the WLC to 8.10.181.0 or later.May...
Resolved! IPSK VLAN Tagging?
Hello,I'm a little confused about the VLAN tagging on IPSK and couldn't find an answer in a guide anywhere.We are not using radius and have several different identities defines in group policy. Each identity has a different VLAN assigned in the Group...
so my current setup is with 2 1142N AP's and a CT5508 and when I do a Local Speed test the fastest I can get to is 60Mbp/s which is far less than the 100Mbbp/s I expect. are there any settings I can check? I understand that this is a very Open questi...
