On 9800L WLCs there are several access points C9120AXI-S, which are using 20MHz channel width instead of configured global value 40 MHz.Is it a bug or a feature ?!
Forum Posts
Can a Cisco Wireless AP License Purchased in Vietnam Be Used on a WLC in China?
Doing an AP build out running 17.6.4 code on physical 9800-40 units and suddenly the tagging stopped working with no changes to the configuration. Probably need to open a TAC case but wondering if anyone has seen this, maybe a bug. Thanks.
Hi Team,Our team from USA is shipping below Cisco Meraki to India but our clearing agent is requesting BIS Certificate for Cisco Meraki.Cisco Meraki MX67 & Cisco Meraki MS120 24PCan you please help BIS for both Model so we ship Cisco Meraki from USA ...
Hi, We have bought some Cisco 3802 Ap's. I connected 1 of the AP's to a switch we have at our office to see if it worked and it did. I read that there has been some bugs with the AP where if you connect it to a 100mbps port it will show you the "ap...
Is it possible to run the "first time setup" of a 9800 via the SP port?For remote site installation, it is sometimes difficcult to set up remote screen share session with a distant site to run the initial dialog; while getting basic access through th...
Resolved! Cisco WLC3502 with Meraki setup
Hi,We are inprocess of planning to setup Branch A office to meraki from Cisco. we have Cisco wlc 3502 in Branch A office and APs in Branch B are connected to it.my question is will Cisco WLC3502 connected to MS120 will work same as it is working now(...
Hi, I have two cores, but there is only a layer 3 connection available . There isn't a layer 2 adjacency between the cores. .If core 1 malfunctions, is it possible to establish a redundant link to core 2?Thanks
Consoled into a 9800 today, created a new user, then logged into the GUI and did the Day 0 configuration. Reconnected to the GUI and was able to do a good bit of the configuration from there; I also tried to ssh to the WLC and enter some configurati...
Resolved! Meraki MR76 AP doesn't start up
Hello,We have purchase a lot of MR76 APs lately to expand / upgrade our Wi-Fi networks on two sites. Most of them were setup and installed ok, however I received one device from another site that is not loading up.Short description. Meraki AP MR76 LE...
FW1:WAN 1 (dynamic public IP)WAN 2 (dynamic public IP)FW2:WAN 1 (dynamic public IP)WAN 2 (static public IP)AP: 1,2,3 (meshed)Now, several PC have to access a specified website that only FW2:WAN2 static IP is allowed to, one hour per month on average....
Hi there,Having several setups of WLANs with AP1832I-E-K9C.Was wondering if it is possible to do hard reset of all of them via the controller, or if it is better or only possible to do it accessing the AP locally?Also how to verify latest firmware an...
Resolved! 1562 RAP reboots after MAP joins.
Hi. I configured a mesh between two 1562 APs and the root reboots within a few seconds after the MAP connects. I was getting the below error but it does not show up in the logs anymore. Basically the MAP joins, all is well for a maybe 20 seconds and ...
Hello All, Required help . We have multiple access points at customer office . Currently customer is only reporting issue for some access points . Access point model is AIR-CAP3702I-E-K9 . WLC model :AIR-CT5508-K9, Current IOS:8.5.171.0Symptoms : Tea...
Hi Community,We want to design a workaround when APs in a plant continues working when the WLC and VLAN CAPWAP goes Down.Now, the AP switchport is in mode access and AP works in mode local.We need to keep one SSID associated to one VLAN UP when the W...
