Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello Cisco WLAN expert,in the dawn of a planned SW-Upgrade on our 9800-80-WLC 17.9.5 it was suggested to reboot all APs on beforehand.Unfortunately several 9130-APs did not survive the procedure and struggle to boot up again correctly apparently. W...
We have a 9800-40 HA SSO pair running 17.9.5 controlling almost all 2800-series APs with a handful of older 3702I APs. The 3702I is no longer supported after 17.9.8. We purchased all new 9172I APs to replace them, but those are not supported until 17...
Hi,I can't see profile of new AP on ISE.Can anyone help me create or Import new Profile for AP CW9176I. We have ISE 3.1 for AP profiling. Thankyou in advance. Regards,Aamir Bhatti
Hi Guys; We have a pair of 9800-40 in HA SSO with RP only. When we first installed it was version 16.12.4. We upgraded to ver 17.3.3 patch 4 and want to enable RMI+RP. Which is the correct procedure? Enable RMI+RP under Administration-->Device, assig...
WIth C9800-L-F-K9 model, i have a Anchor and foreign setup with mobility tunnel formed between them. It is observed that if i switchover anchor WLC (HA-SSO), the mobility tunnel does not come up. I tried changing mobility mac to static.the WMI gatewa...
Hi there, I'm currently using CISCO AIR-CAP3502E-C-K9 APs that already has Autonomous software in it (ap3g1-k9w7-xx.153.3.JF5). My concerns is that, using internet source that has 150 Mbps bandwith, when connected to the AP, the AP can only deliver b...
Hello, how do I reach CCW-R? Is it from within CCW, or there is a separate link?
Trying to get it to boot to ROMMON. Holding button, release @ 20-30 sec, hit ESC....DOES NOT WORK.
I have successfully enabled PIV authentication for CLI via ISE. However, web does not work, gives me openresty error after entering my PIN. Background - I am with DOI and obtained a certificate for the WLC from the DOI CA. Our PIV cards are provid...
Hi all,Currently we are having Cisco 9300 Embedded Wireless LAN Controller as Fabric the fabric WLC in the SDA environment of the Catalyst Center.We are going to migrate this existing EWC WLC with C9800 WLC HA pair.I need your idea for the migration ...
Hi AllI have recently been purchasing the Cisco Meraki CW9164i access points, however after a discussion I believe lots of companies like Ruckus, Aruba etc are now pushing Wifi 7.I looked at pricing this morning for the CW9164i vs the CW9172i access ...
Hi,I have 10 access points deployed on one floor, but most clients keep connecting to a single AP in one area. This causes connectivity problems and slow browsing, especially for new clients trying to join. How can I resolve this issue and ensure pro...
Resolved! C9105AXW-E ap's will not boot
Hello, WLC 9800-CL-40, with software 17.12.6aThe ap's may have been offline for a long time...The boot process stops, see attachment Boot.txt, and a factory reset does not work, see Reset.txt.Any suggestions for a solution?RegardsJohann Folkestad
I have two Cisco 9800-CL WLCs in the same mobility group:WLC-1: 192.168.138.130/24WLC-2: 192.168.138.132/24UDP 16666 is allowed between them, DTLS is enabled, and keepalives are exchanged.However, I keep getting:I’ve checked mobility peer cofig, NTP ...
Hi Guys, I'm running EWC on 9120AXI-E and have a mixed environment of 9120AXI and 1832i AP in lightweight mode.Currently, EWC is running version 17.6.8 (17.06.08.0.7919) and AP are running Image 17.6.8.3 (ap1g4 or ap1g7 depending on the AP model).Whe...
