Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
HI,I have a c9800 controller and i have configured an ssid with static wep authenticationBelow are the logs of affected client2022/08/09 08:02:38.566839 {wncd_x_R0-0}{1}: [dot11] [25451]: (ERR): MAC: 5ce0.c5da.5598 Failed to dot11 parse assoc packet....
Hi community. I have installed an vWLC AIR-CTVM-K9, version 8.5.182.0 - straight from the .ova with standard config. in my ESXI 6.7, Meaning I haven't changed anything.I have a couple of AP's cisco AIR-CAP2702I-E-K9 - Cisco IOS Software, C2700 Softw...
I have a 9800-L-F currently running 17.3.5b (though this was happening on 17.3.x as well). With either ip tacacs source-interface GigabitEthernet0 or ip tacacs source-interface GigabitEthernet0 vrf Mgmt-intf commands configured, the WLC still uses vl...
1) Can we configure AP AIR-CAP370I-E-K9 (atonomous)t o make the user from the organization to authrize automaticaly by MAC filtering without provide any credential.? how ?2) (atonomous) can we create guest access with limited time access. how ?I do...
Hi can some one please clarify the following:1. For new Catalyst APs for use with 9800 WLC, for the UK should these still be ordered as E domain or RoW?2. For Catalyst APs for management by the Meraki Dashboard, again should these be RoW/E or is this...
Cisco Catalys AIR-28000How do I find Filename 0A0A0A64.img to recover access point.u-boot>> printBOOT=part1CASset=maxENABLE_BREAK=1FACTORY_RESET=0MALLOC_len=5MANUAL_BOOT=0MEMORY_DEBUG=0MPmode=SMPautoload=yesbaudrate=9600bootdelay=3cacheShare=nodisaMv...
I'm replacing my Cisco 5520 with a 9800 and am having an issue with RADIUS accounting. On the 5520 I was able to create an accounting server with the IP address of my web content filter. That way, when a user connects to the wireless using their AD...
I have more than 5 "AIR-CAP1702i-E-K9" devices. all pre used now all of them are factory reset.should i have to configure one by one or is there any way to configure on one go ? how to make the users inside the same network auto athenticate to the...
I am setting up my lab with 2800 mobility express controller. I am trying with tagging management vlan.wlc management ip: 10.106.59.190management vlan: 59vlan 58 is for AP's.Here is my switchport configuration:interface GigabitEthernet1/0/5descriptio...
You can create DHCP pool in EWC. However, connecting to the SSID does not renew the IP. Do I need to create a DHCP pool and then do the following?
Hi Guys, We are running AP replacement project and while replacing old AP with new AP, AP are taking more time to download image from WLC during association. (this may be due to site WAN is having low Bandwidth) My query is, is there any way if we ca...
I've connected 9124AXI on a POE+ switch and the AP is complaining about that it wants UPOE, but POE+ is good enough.The thing is that this causes the LED to flash between red and green because it's complaining about not enough power. Planning on usin...
Hi, What is the meaning of this message? How to solve this issue? Can we change WLC emergency version? Does it have downtime? Thank you.
AP and WLC are connected to each other through VPN, and they are sufficiently joined so that they can be used. However, after the VPN is disconnected, the AP is disconnected from the WLC, and when the VPN is reconnected, the AP cannot rejoin the WLC....
We are deploying Cisco 9124s vertically on poles. I read that Cisco recommends using solar shield in outdoor deployments in direct sunlight, but in the installation documentation, the deployments it shows using the solar shield horizontally to shade ...
